Mercury 135 Verado FourStroke Скачать руководство пользователя страница 106

Страница: 106 / 123

Starter Motor Will Not Crank the Engine

POSSIBLE CAUSES

•

Lanyard stop switch not in RUN position.

•

Blown 5‑amp fuse. Check DTS power harness circuit fuse. Refer to

Maintenance

section.

•

Remote control is not shifted to the neutral position.

•

Shift actuator failure. Turn ignition key switch off to reset and then start

the engine.

•

Weak battery or battery connections are loose or corroded.

•

Ignition key switch failure.

•

Wiring or electrical connection faulty.

•

Starter motor solenoid or start solenoid failure.

Engine Will Not Start

POSSIBLE CAUSES

•

Incorrect starting procedure. Refer to

Operation

section.

•

Old or contaminated gasoline.

•

Fuel is not reaching the engine.

• Fuel tank is empty.
• Fuel tank vent not open or restricted.
• Fuel line is disconnected or kinked.
• Fuel filter is obstructed. Refer to

Maintenance

section.

• Fuel pump failure.
• Fuel tank filter obstructed.

•

Ignition system component failure.

•

Spark plugs fouled or defective. Refer to

Maintenance

section.

Engine Starts But Will Not Shift Into Gear

•

Throttle only mode is engaged.

•

Shift actuator failure. Turn ignition key switch off to reset and then start

the engine.

Engine Runs Erratically

POSSIBLE CAUSES

•

Overheating—warning horn not working.

•

Low oil pressure. Check oil level.

•

Spark plugs fouled or defective. Refer to

Maintenance

section.

•

Incorrect setup and adjustments.

•

Fuel is being restricted to the engine.

TROUBLESHOOTING

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды