
INSTALLATION
3-5
MA-5066-ENG
PS200 DRUM MELTER MANUAL
Hoses and applicators connection
PS200 drum melters use standard Meler components. The entire range of
Meler hoses and applicators may be connected to this equipment.
Up to four hose-applicator outputs may be connected to drum melter.
Warning:
When connecting the hose-applicator outputs, verify that the power
to which the equipment is connected does not exceed the maximum allowable
power for each outlet.
PS200 has a hydraulic manifold with 3 available connections. If you connect
only one hose do it in order to facilitate the installation and the connection of
the hose. It will be a benefit for the life of the hose and its correct operation.
Precautions:
• Identify each hose-applicator unit according to the electrical
connection it uses. This is necessary in order to visually control the
temperatures and to observe any possible alarm signals.
• Use the adapters that are the most suitable for each installation,
in order to minimize the space taken up by the hoses. Some
configurations may cause very small radius curves that may cause
inside damage to the hose.
• Save the threaded caps that are removed from the distributor to
connect the hoses. In the future, they may be necessary if a hose is
disconnected from its position.
• Complete the electrical connections for the hoses and applicators
with the equipment turned off. Failure to do so may result in electrical
defects to the connection and cause alarm messages to appear on the
melting equipment display screen.
Parameter Programming
Once the melter and its components are installed, you will need to program
the operational parameters appropriate for the specific application that will be
performed.
PS200 drum melters simplify this task as much as possible, allowing the
operator to modify only those parameters that are necessarily variable for
each application.
Among the various parameters, it is necessary to program the set point
temperature values for each component connected and the value for
overheating warnings. There are two other parameters (weekly start-up and
shut-down programming and the standby temperature value) left to program
in advanced systems, although the factory default values are perfectly valid for
operational purposes.
Programming working temperatures
The melters leave the factory with the following set point temperatures:
11
22
33
44
11
22
33
Содержание PS200
