Meinberg M900 Скачать руководство пользователя | Manualshive

Страница: 66 / 170

background image

Network interface specific configuration

The interface specific parameters can be found in the Interface section. If your

LANTIME is equipped with only one network interface, you will find only one sub
section (Interface 0). Otherwise you see a sub section for each installed Ethernet port.

Here, the parameters for the network port can be changed. In the upper section of the
page you can enter the IPv4 parameters, the lower part gives you access to the IPv6
parameters of the interface.

IPv4 addresses and DHCP

IPv4 addresses are built of 32 bits, which are grouped in four octets, each

containing 8 bits. You can specify an IP address in this mask by entering four decimal
numbers, separated by a point “.”.

Example: 192.168.10.2

Additionally you can specify the IPv4 netmask and your default gateway address.

Please contact your network administrator, who can provide you with the settings
suitable for your specific network.

If there is a DHCP (Dynamic Host Configuration Protocol) server available in your
network, the LANTIME system can obtain its IPv4 settings automatically from this
server. If you want to use this feature (again, you should ask your network
administrator whether this is applicable in your network), you can change the DHCP
Client parameter to “ENABLED”. In order to activate the DHCP client functionality,
you can also enter the IP address “000.000.000.000” in the LCD menu by using the
front panel buttons of the LANTIME. Using DHCP is the default factory setting.

The MAC address of your timeserver can be read in the LCD menu by pressing the
NEXT button on the front panel twice. This value is often needed by the network
administrator when setting up the DHCP parameters for your LANTIME at the
DHCP server.

If the DHCP client has been activated, the automatically obtained parameters are
shown in the appropriate fields (IPv4 address, netmask, gateway).

IPv6 addresses and autoconf

You can specify up to three IPv6 addresses for your LANTIME timeserver.

Additionally you can switch off the IPv6 autoconf feature. IPv6 addresses are 128 bits
in length and written as a chain of 16bit numbers in hexadecimal notation, separated
with colons. A sequence of zeros can be substituted with “::” once.

66

«
...
64
65
66
67
68
...
»

Содержание M900











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M900

Бренд: Far south networks Страницы: 4

RS/6000 7043 43P Series

Бренд: IBM Страницы: 322

System x3400 M3 Types 7378

Бренд: IBM Страницы: 45

Бренд: Aastra Страницы: 502

Бренд: B&B Electronics Страницы: 67

NPort IA5250I/5250I-T Series

Бренд: Moxa Technologies Страницы: 2

Бренд: Fujitsu Siemens Computers Страницы: 68

Бренд: Discover Video Страницы: 148

Multi-Port Fast Ethernet Print Server FPS-3121

Бренд: Planet Страницы: 57

Бренд: Super Страницы: 60

Бренд: Red Hat Страницы: 120

Бренд: Black Box Страницы: 3

Бренд: Promise Technology Страницы: 259

Бренд: Inspur Страницы: 2

Бренд: YASKAWA Страницы: 21

Бренд: Inspur Страницы: 86

Codec Engine Server

Бренд: Texas Instruments Страницы: 36

Бренд: Lantronix Страницы: 190

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды