Meinberg M900 Скачать руководство пользователя | Manualshive

Страница: 52 / 170

background image

Menu: PTP IEEE 1588

The Precision Time Protocol (PTP) IEEE1588 is an optional network card with a

special hardware time stamping unit to realize the high precision timing in the range
of nanoseconds via Ethernet network.

Menu: PTP V1

This menu reflect the main parameters:

The „PTP Port Conn“ signals if any hardware time stamping with PTP packets is
active or not. If the state “no” will be displayed please check the following
conditions:

- Is an Ethernet cable connected to the PTP port and the LINK is up?
- Is the PTP port configured with a valid IP address and netmask?
- Is the Default Gateway configured?
- Check if Multicast enabled your network environment (Switch or Router).
- Are there any other PTP Master in your network?

The stratum value reflects the PTP stratum in a range from 1 to 255. The „State:“ will
show the current PTP state PTP_MASTER, PTP_SLAVE, PTP_LISTENING and
PTP_PASSIVE. The last line shows the GM UUID: this is the MAC address of the
current PTP Grandmaster in your network. When pressing “OK” you can change PTP
specific parameters:

52

-> PTP V1 <-

PTP V2

PTP Port Conn:ok

Stratum:11 PM:-

PTP MASTER

00:00:00:00:00:00

Mode:PTP_MASTER

Pref.M: disabled

Sync Rate[2^x]:1

Sub Domain: 0

«
...
50
51
52
53
54
...
»

Содержание M900











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M900

Express5800/T110g-E

Бренд: NEC Страницы: 2

APSolute Vision

Бренд: Radware Страницы: 81

Бренд: Omega Страницы: 49

Бренд: Iwatsu Страницы: 338

SUPERO SuperServer 1018L-MP

Бренд: Supermicro Страницы: 104

Бренд: Discover Video Страницы: 148

Бренд: TYAN Страницы: 80

B8236G70W8HR-HE

Бренд: TYAN Страницы: 84

Бренд: TYAN Страницы: 82

SILVERSTREAM 3.75

Бренд: RSA Security Страницы: 11

Бренд: CryptoTelecom Страницы: 86

Бренд: Aviosys Страницы: 30

Бренд: Supero Страницы: 98

Dual Processor AS 1020C-3

Бренд: Supero Страницы: 106

Бренд: Lantronix Страницы: 93

Бренд: Seagate Страницы: 69

Solaris Cluster 3.3

Бренд: Oracle Страницы: 56

Fike Cheetah FS-8700-48

Бренд: FieldServer Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды