Meinberg M900 Скачать руководство пользователя | Manualshive

Страница: 41 / 170

background image

Menu TIME CODE IRIG (Output)

This menu lets the user select the time code to be generated by GPS-TC. Most

IRIG-Codes do not carry any time zone information, hence UTC is selected for output
by default. If desired, the clocks local time can be output by selecting "TIME:
LOCAL".

Refer to chapter

Timecode

for details.

Menu Synthesizer Frequency Output

This setup menu lets the user edit the frequency and phase to be generated by the

on-board synthesizer. Frequencies from 1/8 Hz up to 10 MHz can be entered using
four digits and a range. The range can be selected if the „UP“ or „DOWN“ key is
pressed while the cursor is positioned on the frequency´s units string. If the least
significant range has been selected valid fractions of the frequency are .0, .1
(displayed as 1/8), .3 (displayed as 1/3), .5 and .6 (displayed as 2/3). Selection of 1/3
or 2/3 means real 1/3 or 2/3 Hz, not 0.33 or 0.66. If frequency is set to 0 the
synthesizer is disabled.

The last line of the display lets the user enter the phase of the generated frequency
from -360° to +360° with a resolution of 0.1°. Increasing the phase lets the signal
come out later. Phase affects frequencies less than 10.00 kHz only, if a higher
frequency is selected a message "(phase ignored)" informs the user that the phase
value is ignored.

41

IRIG Output

Code:
B002+B122

Time: UTC

Enable Outputs

Serial Outputs

> IRIG Output <
Pulse Outputs

Synthesizer
Frequency:

0100 Hz

Phase: 090.0 el

«
...
39
40
41
42
43
...
»

Содержание M900











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M900

Бренд: F5 Страницы: 72

Бренд: US Robotics Страницы: 36

Anybus Communicator ABC4018

Бренд: HMS Networks Страницы: 64

Бренд: PRIMERGY Страницы: 87

DiskStation Series

Бренд: Synology Страницы: 6

eserver iSeries 270

Бренд: IBM Страницы: 40

Бренд: Belkin Страницы: 2

WSG SoundGrid Server One

Бренд: Waves Страницы: 4

Бренд: Xerox Страницы: 13

6100BD - Phaser Color Laser Printer

Бренд: Xerox Страницы: 34

6100BD - Phaser Color Laser Printer

Бренд: Xerox Страницы: 140

Бренд: Zonet Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: Viavi Страницы: 7

Бренд: Datum Страницы: 54

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

TEW-P1UG - Wireless Print Server

Бренд: TRENDnet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды