Meinberg M900 Скачать руководство пользователя

Страница: 4 / 170

Root Menu........................................................................................................... 31

Menu: Reference Time.............................................................................................33

Menu: Info GPS................................................................................................... 33

GPS Status & Version..........................................................................................34

GPS Receiver Position.........................................................................................34

GPS Satellite Constellation..................................................................................35

Menu: Setup GPS.................................................................................................35

Set Antenna Cable Length................................................................................... 35

Set GPS Receiver Simulation Mode.................................................................... 36

Menu: Init GPS.................................................................................................... 36

Initiate Cold Boot of GPS Receiver.....................................................................36

Initiate Warm Boot of GPS Receiver...................................................................37

Init Receiver Position...........................................................................................37

Init Receiver Time............................................................................................... 37

Menu: Setup GPS Outputs................................................................................... 38

Enable Outputs.....................................................................................................38

Setup Serial Outputs............................................................................................ 39

Setup Time Zone..................................................................................................40

Menu TIME CODE IRIG (Output)......................................................................41

Menu Synthesizer Frequency Output...................................................................41

Programmable pulse (Option)..................................................................................42

SETUP POUT X.................................................................................................. 42

Mode.................................................................................................................... 42

Timer mode..........................................................................................................43

Single Pulse..........................................................................................................43

Cyclic mode......................................................................................................... 44

PPS, PPM, PPH Modes........................................................................................44

Menu: PZF Reference Time.....................................................................................45

Info PZF............................................................................................................... 45

Status & Version.................................................................................................. 45

Correlation & Field.............................................................................................. 45

Setup PZF.............................................................................................................46

Transmitter Distance............................................................................................ 46

Ignore Lock (Simulation Mode).......................................................................... 47

Initial Time...........................................................................................................47

Setup Serial Out................................................................................................... 47

Menu: Time Service.................................................................................................48

Menu: external NTP server.................................................................................. 48

Menu: Stratum of local clock...............................................................................49

Menu: Reset Time................................................................................................49

Menü: 2nd Receiver............................................................................................. 50

Menu: PTP IEEE 1588.........................................................................................51

Menu: PTP V1......................................................................................................... 51

Menu: PTP V2......................................................................................................... 52

Menu: Network........................................................................................................ 54

Menu: Global Configuration................................................................................55

Menu: Network Interfaces................................................................................... 56

Содержание M900











































































































































































Результаты поиска

Содержание M900

Отзывы:

Похожие инструкции для M900

Бренды по названию

Популярные бренды

Meinberg M900, Руководство по эксплуатации

Результаты поиска

Содержание M900

Отзывы:

Похожие инструкции для M900

Бренды по названию

Популярные бренды