Medin medinCNO Скачать руководство пользователя страница 59

Страница: 59 / 68



+49 8142 448 460

[email protected]

www.medin-medical.com

medin Medical Innovations GmbH

Adam-Geisler-Str. 1

D-82140 Olching

OP_medinCNO EN

Rev 12 Stand 06.03.2019

von

The power supply unit may only be repaired by authorized specialists.

Warning:

To avoid an electrical shock, the housing of the power supply unit of the medinCNO

should not be opened.

Modification of the power supply unit is not permitted (termination of the warranty).

9.6

External filter

The filter must be cleaned every 2 months by tapping or knocking (dry). The filter needs to be replaced after

12 months.

To change the filter, the filter grid must be pulled out from behind. The filter can be removed and cleaned. The

filter grid together with the filter is then pushed back in as far as the stop. You will hear a click as it snaps into

place.

Figure 6: External filter

Please note:

Only a type PPI 30 filter should be used.

Содержание medinCNO





































































Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды

Medin medinCNO, Руководство пользователя

Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды