Medin medinCNO Скачать руководство пользователя страница 25

Страница: 25 / 68



+49 8142 448 460

[email protected]

www.medin-medical.com

medin Medical Innovations GmbH

Adam-Geisler-Str. 1

D-82140 Olching

OP_medinCNO EN

Rev 12 Stand 06.03.2019

von

Figure 4-2: Battery charge status displayed in the top left-hand area of the screen

The charge status of the internal battery is displayed in the top left-hand area of the medinCNO

screen.

Attention:

When the medinCNO

is running on battery power, an alarm is sounded when the internal battery is low. It

must then be immediately connected to an external power source, as otherwise the medinCNO

will stop

working.

To disconnect the medinCNO

from the mains, the plug of the power supply unit of the medinCNO

must be

pulled out of the electrical outlet. Otherwise the medinCNO

is still connected to the mains, even when it is

turned off.

Therefore, when setting up the medinCNO

, it should be ensured that the plug of the power supply unit is still

accessible even when set up and the medinCNO

can thus be easily disconnected from the mains.

Disconnect the power supply unit from the mains during thunderstorms.

Warning:

Since the surface temperature of the power supply unit can become too hot for the patient, it should always

be ensured that the power supply unit is not within the patient's reach.

The plug of the power supply unit of the medinCNO

must also always be freely accessible even when set up,

in order to allow the medinCNO

to be quickly disconnected from the mains in the event of a hazardous

situation.

Do not insert the power supply plug of the medinCNO

into ceiling outlets since, due to its weight, it can be

pulled out of the outlet in this case.

Содержание medinCNO





































































Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды

Medin medinCNO, Руководство пользователя

Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды