Medin medinCNO Скачать руководство пользователя страница 23

Страница: 23 / 68



+49 8142 448 460

[email protected]

www.medin-medical.com

medin Medical Innovations GmbH

Adam-Geisler-Str. 1

D-82140 Olching

OP_medinCNO EN

Rev 12 Stand 06.03.2019

von

First Use

The CPAP system must be set up and the device checked before starting any CPAP therapy using the

medinCNO

. This check starts automatically whenever the device is started up.

The device should not be connected to a patient during set-up and system start. In addition, during set-up,

system start and operation, the user should not simultaneously touch the patient and the device. This applies

above all to the power supply, the alarm, RS232 or USB interface and the accessible metal parts of the

pneumatic unit (gas connections, overpressure valve and mounting screws).

Warning:

If errors are detected when the medinCNO

is checked before first use, if the medinCNO

is found to be

damaged or does not behave as expected or as intended in the user manual, it must not be connected to a

patient under any circumstances.

The power supply unit should not be used if it has visible damage to the housing or cord.

The power supply unit should not be used in the direct vicinity of the patient since there may be temperatures

of >71°C.

4.1

CPAP system components

A CPAP system based on a medinCNO

comprises the following components:

A CPAP driver: the medinCNO

A Medijet

nCPAP generator together with a suitable prong or mask

An active respiratory gas humidifier to humidify the respiratory gas (recommended)

A patient tube circuit set that fits the patient gas outlet, CPAP pressure meter inlet of the

medinCNO

, the Medijet

and the humidifier selected

A bonnet of the correct size

A system for monitoring the patient’s oxygen saturation and checking the efficacy of CPAP therapy

(this is an essential condition for the use of the medinCNO

)

Please note:

The medinCNO

should always be used in combination with an active respiratory gas humidifier in order to

avoid the patient’s airways drying out and cooling.

Содержание medinCNO





































































Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды

Medin medinCNO, Руководство пользователя

Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды