McHale 900340 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 155

background image

McHale

Fusion Vario

Baler & Wrapper

17

3.7 Trained operator criteria

3.8 Operating the machine

In order to avoid serious injury or even death by being pulled into the machine:



Never attempt to feed net or crop into the baling chamber or attempt to unplug
the pick-up area while the baler is running.



Disengage the PTO, apply the hand brake, shut the tractor engine off and
remove the key from the ignition.

3.9 In the event of a fire

In the event of a fire, it is the operator’s decision to determine the
seriousness and hence the solution to the situation. The following is
given only as a guideline procedure:

Age related requirements

General requirements

18 +

The operator needs to be fully
trained in the use of this machine
and have a valid tractor driver’s
licence.



The operator must be in full
control of his/her senses and
must not be under the influence
of any alcohol or drugs,
prescribed or otherwise.



The operator must have read
and understood all aspects of the
operator manual in order to
operate, maintain and clean the
machine. Ideally, they should
also receive training from their

McHale

Dealer.



It is only acceptable to have
more than one person in the
tractor cab, if it has a second
seat.

16 - 18

An operator between the age of 16
and 18 years old must have a
provisional licence and must be
accompanied by an experienced
driver/operator, at all times, even
during maintenance and cleaning!

< 16

Persons younger than 16 years of
age are not allowed to operate,
clean or carry out maintenance on
this machine, under any
circumstances!

WARNING: Never clear a blockage while the machine is in operation!

Never attempt to clear a blockage while the machine is in operation. You
could be severely injured or pulled in by the rotating tines!

WARNING: Stand well clear of the machine while it is in operation!

Stand well clear of the machine and tractor when the machine is
operating. Objects such as loose tines, stones and other debris may be
discharged from the machine.

«
...
15
16
17
18
19
...
»

Содержание 900340




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 900340

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: VACGEN Страницы: 13

4 Happy Kids GUCIO

Бренд: 4iQ Страницы: 12

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Gainsborough Страницы: 2

Бренд: Gainsborough Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды