Majestic MERID36 страница 39 Скачать руководство пользователя

Страница: 39 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

Venting and Chimneys

A. Assemble Vent Sections
(DVP Pipe Only)

Attach Vent to the Firebox Assembly
Note:

The end of the pipe sections with the lanced tabs

will face toward the appliance.
Attach the first pipe section to the starting collar:
•  Lanced pipe end of the starting collar.
•  Inner pipe over inner collar.
•  Push the pipe section until all lanced tabs snap in place.
•  Lightly tug on pipe to confirm it has locked.

Figure 7.2

Figure 7.3

Assemble Pipe Sections

Per Figure 7.2:

• Start the inner pipe on the lanced end of section A into

the flared end of section B.

• Start the outer pipe of section A over the outer pipe of

section B.

• Once both vents sections are started, push firmly until

all lanced tabs lock into place.

• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13

mm) to hold outer pipe sections together. If predrilling holes,

DO NOT

penetrate inner pipe.

For 90º and 45º elbows that are changing the vent direction

Required Commercial, Multi-family (Multi-level exceeding

two stories), or High-Rise Applications

All outer pipe joints must be sealed with 100% silicone

(300 ºF minimum continuous exposure rating), including

the slip section that connects directly to the horizontal ter

mination cap.
• Apply a bead of silicone sealant (300 ºF minimum con

tinuous exposure rating) inside the female outer pipe

joint prior to joining sections. See Figure 7.1.

Apply a bead of silicone sealant (300 ºF minimum con

tinuous exposure rating) to the outside of connecting

joint after joining sections

Apply aluminum foil tape (300 ºF minimum continuous

exposure rating) to the outside of connecting joint after

joining sections. On horizontal pipe runs, it is recom

mended that the tape seam is positioned on the bottom

side of the vent pipe.

• Only outer pipes need to be sealed. All unit collar, pipe,

slip section, elbow and cap outer flues shall be sealed

in this manner, unless

otherwise stated.

WARNING! Risk of Fire or Explosion! DO NOT

break

silicone seals on slip sections. Use care when remov-

ing termination cap from slip pipe. If slip section seals

are broken during removal of the termination cap, vent

could leak.

Figure 7.4 Seams

Note:

Make sure that the

seams are not aligned to prevent

unintentional disconnection.

INCORRECT

CORRECT

Lances

Figure 7.1 High Temperature Silicone Sealant

from horizontal to vertical, one screw minimum should be put

in the outer flue at the horizontal elbow joint to prevent the

elbow from rotating. Use screws no longer than 1/2 in. (13

mm). If predrilling screw holes,

DO NOT

penetrate inner pipe.

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды

Majestic MERID36, Руководство по установке

Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды