Majestic MERID36 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 75

background image

6

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

2

Getting Started

A. Design and Installation Considerations

Majestic direct vent gas appliances are designed to oper

-

ate with all combustion air siphoned from outside of the

building and all exhaust gases expelled to the outside. No

additional outside air source is required.

Installation MUST comply with local, regional, state and

national codes and regulations. Consult insurance carrier,

local building inspector, fire officials or authorities having

jurisdiction over restrictions, installation inspection and

permits.

Before installing, determine the following:

•  Where the appliance is to be installed.
•  The vent system configuration to be used.
•  Gas supply piping requirements.
•  Provisions for optional heat management system.
•  Electrical wiring requirements.
•  Framing and finishing details.

• Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualified

service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following

tools and building supplies are available.
Tape measure

Framing material

Pliers

Non-corrosive leak check solution

Hammer

Phillips screwdriver

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Flat blade screwdriver

1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300 ºF minimum continuous exposure

rating)

One 1/4 in. female connection (for optional fan).

Figure 2.1 Good Faith Wall Surface Temperatures Above Appliance

B. Good Faith Wall Surface

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

6 in.

18 in.

24 in.

30 in.

TO CEILING

12 in.

127°F

123°F

132°F

135°F

147°F

APPLIANCE FRONT

FIREPLACE

OPENING

Installation and service of this

appliance should be performed

by qualified personnel. Hearth &

Home Technologies recommends

NFI certified professionals.

NOTICE:

Temperatures listed above are taken with a

temperature measuring probe as prescribed by the test

standard used for appliance certification. Temperatures

on walls or mantels taken with an infrared thermometer

may yield increased temperatures of up to 30 degrees or

more depending on the thermometer settings and material

characteristics being measured. Use appropriate finishing

materials that are able to withstand these conditions. For

additional finishing guidelines, see Section 10.

If installing a television (TV) above the appliance, see

Section 3 of the appliance Owner’s Manual.

«
...
4
5
6
7
8
...
»

Содержание MERID36












































































Отзывы:

Нет отзывов

Похожие инструкции для MERID36

Бренд: Majestic fireplaces Страницы: 28

Бренд: Majestic fireplaces Страницы: 52

Бренд: Majestic fireplaces Страницы: 4

Бренд: Majestic fireplaces Страницы: 24

Бренд: Majestic Страницы: 64

Royal Collection WMC36

Бренд: Majestic fireplaces Страницы: 8

PerfectView 33LDV

Бренд: Majestic fireplaces Страницы: 4

Бренд: Vanguard Страницы: 32

Imperial Carousel

Бренд: Malm Fireplaces Страницы: 8

Бренд: Escea Страницы: 2

Бренд: Vanguard Страницы: 30

Бренд: Paramount Fitness Страницы: 14

Alcoi GF201300BK

Бренд: Moda flame Страницы: 9

Ascent BHD4PFCNA

Бренд: Napoleon Страницы: 140

Бренд: Majestic Страницы: 24

Бренд: Lennox Hearth Products Страницы: 16

Бренд: Capital fireplaces Страницы: 4

COALFLAME BR627

Бренд: Valor Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды