Majestic MERID36 Скачать руководство пользователя страница 51

Страница: 51 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

B. Mantel and Wall Projections

WARNING! Risk of Fire!

Comply with all minimum clear-

ances as specified. Framing closer than the minimums list

ed must be constructed entirely of noncombustible materials

(i.e., steel studs, concrete board, etc.)

Figure 10.5 Combustible Mantel Leg or Wall Projections

(Acceptable on both sides of opening)

Figure 10.3 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

2-1/2

TO CEILING

Measurement from fireplace

opening to bottom of appliance:

= 33-1/2 IN. (MERID36IN/MERID36IL)

= 35-1/2 IN. (MERID42IN/MERID42IL)

INTERIOR WALL

TOP VIEW

MANTEL LEG OR WALL PROJECTIONS

FIREPLACE OPENING

minimum is ____, then

maximum is_____.

Inches

2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16

Millimeters

113

138

164

189

Inches

∞

Millimeters

102

127

∞

Note:

Measurement is taken from top of the opening,

NOT the top of the fireplace.

Mantels - Combustible

Mantel Legs or Wall Projections - Combustible

Note:

All

measurements

in inches.

Non-combustible Mantels

Note:

All

measurements

in inches.

Figure 10.4 Minimum Vertical and Maximum Horizontal

Dimensions of Non-Combustibles

Figure 10.6 Non-Combustible Mantel Leg or Wall Projections

(Acceptable on both sides of opening)

Non-Combustible Mantel Legs or Wall Projections

minimum is ____, then

maximum is_____.

Inches

0-5-7/16

6-7/16

Millimeters

0-138

164

Inches

∞

Millimeters

152

∞

TO CEILING

Measurement from fireplace

opening to bottom of appliance:

= 33-1/2 IN. (MERID36IN/MERID36IL)

= 35-1/2 IN. (MERID42IN/MERID42IL)

INTERIOR WALL

TOP VIEW

MANTEL LEG OR WALL PROJECTIONS

FIREPLACE OPENING

6 IN.

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Majestic MERID36, Руководство по установке, Страница: 51 / 75

Результаты поиска

Содержание MERID36

Отзывы: