Majestic MERID36 страница 12 Скачать руководство пользователя

Страница: 12 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

C. Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the

gas appliance and/or its vent system. In cooler climates

the vent should be enclosed inside the chase.

NOTICE:

Treatment of ceiling firestops and wall shield

firestops and construction of the chase may vary with the

type of building. These instructions are not substitutes

for the requirements of local building codes. Therefore,

you MUST check local building codes to determine the

requirements to these steps.

Chases should be constructed in the manner of all out-

side walls of the home to prevent cold air drafting prob-

lems. The chase should not break the outside building

envelope in any manner.
Walls, ceiling, base plate and cantilever floor of the chase

should be insulated. Vapor and air infiltration barriers

should be installed in the chase as per regional codes for

the rest of the home. Additionally, in regions where cold

air infiltration may be an issue, the inside surfaces may be

sheetrocked and taped (or an equivalent method may be

used) to achieve maximum air tightness.
To further prevent drafts, the wall shield and ceiling fire

stops should be caulked with caulk with a minimum of

300 ºF continuous exposure rating to seal gaps. Gas

line holes and other openings should be caulked with

caulk with a minimum of 300 ºF continuous exposure rating

or stuffed with unfaced insulation. If the appliance is being

installed on a cement surface, a layer of plywood may be

placed underneath to prevent conducting cold up into the

room.

NOTICE:

Install appliance on hard metal or wood surfaces

extending full width and depth.

DO NOT

install directly

on carpeting, vinyl, tile or any combustible material other

than wood.

WARNING! Risk of Fire!

Maintain specified air space

clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent

accidental contact.

• The chase must be properly blocked to prevent blown

insulation or other combustibles from entering and

making contact with fireplace or chimney.

• Failure to maintain airspace may cause overheating and

a fire.

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды

Majestic MERID36, Руководство по установке

Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды