Majestic MERID36 страница 47 Скачать руководство пользователя

Страница: 47 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use

with a fan (See Figure 8.3):

• The power supply for the appliance must be brought into

a switch box.

• The power can then be supplied from the switch box to

the appliance using a minimum of 14-3 with ground wire.

• At the switch box connect the black (hot) wire and red

(switch leg) wire to the wall switch as shown.

• At the appliance connect the black (hot), white (neutral)

and green (ground) wires to the junction box as shown.

• Add a 1/4 in. insulated female connector to the red (switch

leg) wire, route it through the knockout in the face of the

junction box, and connect to the top fan switch connector

(1/4 in. male) as shown.

Red

Switch

Switch Box

Red

Black

Green

White

Power

Supply

Wires

White

Minimum 14-3 AWG
with Ground

Junction Box

Knockout

Figure 8.3 Junction Box Wired to Wall Switch

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды

Majestic MERID36, Руководство по установке

Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды