Majestic MERID36 страница 3 Скачать руководство пользователя

Страница: 3 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

Installation Standard Work Checklist

Customer:

Lot/Address:

Model (circle one): MERID36IN MERID36IL

MERID42IN

MERID42IL

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Comments:

Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective

action needed _____________________________________________________________________________________

_________________________________________________________________________________________________

Comments Communicated to party responsible ____________________ by ______________________on ___________

(Builder / Gen. Contractor/) (Installer) (Date)

Appliance Install

YES

IF NO, WHY?

Verified that the chase is insulated and sealed. (Pg. 12)

___________________________

Required non-combustible board is installed. (Pg. 38)

___________________________

Verified clearances to combustibles. (Pg. 10-11)

___________________________

Fireplace is leveled and secured. (Pg. 38)

___________________________

Venting/Chimney Section 5 (Pg 32-34), Section 7 (Pg 39-44)

Venting configuration complies to vent diagrams.

___________________________

Venting installed, locked and secured in place with proper clearance.

___________________________

Elbow heat shield installed per requirements. (Pg 19, 32) ___________________________

Firestops installed.

___________________________

Attic insulation shield installed.

___________________________

Exterior wall/Roof flashing installed and sealed.

___________________________

Terminations installed and sealed.

___________________________

Electrical Section 8 (Pg 45-47)

Unswitched power (110-120 VAC) provided to the appliance.

___________________________

Switch wires properly installed.

___________________________

Gas Section 9 (Pg 48-49)

Proper appliance for fuel type.

___________________________

Was a conversion performed?

___________________________

Leak check performed and inlet pressure verified.

___________________________

Verified proper air shutter setting for installation type.

___________________________

Finishing Section 10 (Pg 50-54)

Combustible materials not

installed in non-combustible areas.

___________________________

Verified all clearances meet installation manual requirements.

___________________________

Mantels and wall projections comply with installation manual requirements.

___________________________

Appliance Setup Section 11 (Pg 55-63)

All packaging and protective materials removed (inside & outside of appliance).

___________________________

Refractories, logs, lava rock, and embers installed correctly.

___________________________

Glass assembly installed and secured.

___________________________

Accessories installed properly.

___________________________

Decorative front properly installed.

___________________________

Manual bag and all of its contents are removed from inside/under

the appliance and given to party responsible for use and operation.

___________________________

Started appliance and verified no

gas leaks exist.

___________________________

2517-982B 3/18



= Contains updated information.

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your file.

• That this checklist remain visible at all times on the appliance until the installation is complete.

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this

installation manual.

WARNING! Risk of Fire or Explosion!

Failure to install appliance according to these instructions could

lead to a fire or explosion.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды

Majestic MERID36, Руководство по установке

Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды