Majestic MERID36 страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 75

background image

38

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

D. Non-Combustible Material Installation

The factory-installed non-combustible board spans the

distance from the top of the fireplace to the center of the

framing header. This board must be used. See Figure 6.14.

WARNING! Risk of Fire!

DO NOT remove factory-

installed non-combustible material.

C. Securing and Leveling the Appliance

WARNING! Risk of Fire!

Prevent contact with:

• Sagging or loose insulation

• Insulation backing or plastic

• Framing and other combustible materials
Block openings into the chase to prevent entry of blown-

in insulation. Make sure insulation and other materials

are secured.

DO NOT

notch the framing around the appliance

standoffs.
Failure to maintain air space clearance could cause

overheating and fire.

The diagram shows how to properly square, position and

secure the appliance. See Figures 6.12 and 6.13. Nailing

tabs are provided to secure the appliance to the framing

members.
•  Bend out nailing tabs on each side.
•  Place the appliance into position.
•  Keep nailing tabs flush with the framing.
•  Level the appliance from side to side and front to back.
•  Shim the appliance as necessary. It is acceptable to use

wood shims underneath the appliance.

• Secure the appliance to the framing by using nails or

screws through the nailing tabs.

• Optional: Secure the appliance to the floor by inserting

two screws through the pilot holes at the bottom of the

appliance.

Figure 6.14 Non-combustible Board

HEADER

Figure 6.13 Proper Positioning and Securing of an Appliance

Figure 6.12 Positioning the Appliance Squarely

A

B

Note: Diagonal dimensions (A) and (B) must be within

1/4 inch of each other.

NAILING TABS

(BOTH SIDES)

PILOT HOLES

«
...
36
37
38
39
40
...
»

Содержание MERID36












































































Отзывы:

Нет отзывов

Похожие инструкции для MERID36

UNI G CHIMNEY 08

Бренд: UNIPRODO Страницы: 11

Бренд: HAMPTON BAY Страницы: 19

Бренд: Dimplex Страницы: 2

Бренд: Fisher Страницы: 16

Бренд: Napoleon Страницы: 28

Ontario APCL**RN

Бренд: Formosa Страницы: 44

Бренд: Kingsman Страницы: 43

EF11-36 LIMOUSIN

Бренд: Focal Point Страницы: 13

Бренд: Vanguard Страницы: 40

Бренд: KEKAI Страницы: 98

Бренд: La Hacienda Страницы: 4

Бренд: Empire Comfort Systems Страницы: 2

Бренд: True North Страницы: 28

Бренд: DutchWest Страницы: 36

Weyland Round Aluminum

Бренд: Fire Sense Страницы: 18

Бренд: Home Depot Страницы: 37

Бренд: KAL-FIRE Страницы: 16

Бренд: Jensen Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды