manualshive.com logo in svg

Majestic MERID36, Руководство по установке

Majestic MERID36 - дивный камин с элегантным дизайном и передовыми возможностями. Установочный руководство и руководство пользователя доступны для скачивания бесплатно с manualshive.com. Наслаждайтесь теплом и красотой этого продукта с помощью наших подробных инструкций.

Поделиться
Скачать
background image

49

Majestic  •  MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual  •  2517-980 Rev. C  •  3/18

Figure 9.1  Air Shutter

Air Shutter Settings (Factory Set to Minimum Vent Run

E.  Air Shutter Setting

Air shutter settings should be adjusted by a qualified ser

-

vice technician at the time of installation. 

The air shutter is 

set at the factory for minimum vertical vent run. Adjust air 

shutter for longer vertical runs. See Figure 9.1.
•  Loosen the wing nut.
•  Move the wing nut to the right to open the air shutter.
•  Move the wing nut to the left to close the air shutter.
•  Tighten the wing nut.

NOTICE: 

If sooting occurs, provide more air by opening 

the air shutter.

MODEL

GAS TYPE

MIN. VENT RUN MAX. VENT RUN

MERID36IN

NG

1/8 in.

Full Open

MERID36IL

PROPANE

3/8 in.

Full Open

MERID42IN

NG

5/16 in.

Full Open

MERID42IL

PROPANE

3/8 in.

Full Open

Note:  

Adjust  air  shutter  after  flame  has  reached  full 

maturity (approximately 20-40 minutes).

AIR SHUTTER 

WING NUT

Minimum and maximum shutter settings are set up to appear like Figure 4.18.  
•  Minimum vent run consists of enough horizontal vent pipe to exit 2 X 6 wall construction (approximately 8 inches).
•  Maximum vent run consists of “H Maximum” on Figure 4.18.

Note:  

All vent runs may need to be evaluated for ideal shutter settings.  Shutter distances may vary due to vent run, fuel 

quality, and elevation.

Содержание MERID36












































































Отзывы:

Нет отзывов

Похожие инструкции для MERID36

Majestic WMII-42AS Installation Manual preview
WMII-42AS
Бренд: Majestic Страницы: 20
Jøtul F 602 ECO Installation And Operating Instructions Manual preview
F 602 ECO
Бренд: Jøtul Страницы: 72
HASE Cartago Operating Instructions Manual preview
Cartago
Бренд: HASE Страницы: 48
Valor BR419 VA Owner'S Manual preview
BR419 VA
Бренд: Valor Страницы: 12
decorflame MM360-52GCN Manual preview
MM360-52GCN
Бренд: decorflame Страницы: 21
Fisher HANMER Installation & Operation Instructions preview
HANMER
Бренд: Fisher Страницы: 16
Majestic Sovereign Series Owner'S Manual preview
Sovereign Series
Бренд: Majestic Страницы: 24
Cal Flame FRP9092 Owner'S Manual preview
FRP9092
Бренд: Cal Flame Страницы: 32
Napoleon EPA 1450 Installation And Operation Instructions Manual preview
EPA 1450
Бренд: Napoleon Страницы: 21
Majestic fireplaces CR36R Homeowner'S Installation And Operating Manual preview
CR36R
Бренд: Majestic fireplaces Страницы: 24
Heat & Glo Tonic SLR-C Installation Instructions preview
Tonic SLR-C
Бренд: Heat & Glo Страницы: 2
Desa MAEF26 Safety Information And Installation Manual preview
MAEF26
Бренд: Desa Страницы: 16
Smart+ Products SPP-IF1500-MOFP Owners Installation And Operating Manual preview
SPP-IF1500-MOFP
Бренд: Smart+ Products Страницы: 9
Improvements 532761 Owner'S Instruction Manual preview
532761
Бренд: Improvements Страницы: 24
Zanussi ZEFIST1001SS User Manual preview
ZEFIST1001SS
Бренд: Zanussi Страницы: 24
Duluth Forge PFS FDLR18-1 Owner'S Operation And Installation Manual preview
PFS FDLR18-1
Бренд: Duluth Forge Страницы: 32
British Fires 18.0 NEW FOREST 1200 Installation And User Instructions Manual preview
18.0 NEW FOREST 1200
Бренд: British Fires Страницы: 49
Outdoor Lifestyles DAKOTA-AU Installation & Operation Instructions preview
DAKOTA-AU
Бренд: Outdoor Lifestyles Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды