Majestic MERID36 страница 45 Скачать руководство пользователя

Страница: 45 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

A. General Information

WARNING! Risk of Shock or Explosion! DO NOT

wire

110-120 VAC to the valve or to the appliance wall switch.

Incorrect wiring will damage controls.

NOTICE:

This appliance must be electrically wired

and grounded in accordance with local codes or, in the

absence of local codes, with

National Electric Code

ANSI/NFPA 70-latest edition

or the

Canadian Electric

Code CSA C22.1.

• Wire the appliance junction box to unswitched 110-

120 VAC. This is required for proper operation of the

appliance.

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in

compliance with the applicable electrical codes, when

it is installed in locations such as in bathrooms or near

sinks.

• Low voltage and 110-120 VAC voltage cannot be shared

within the same wall box.

• In some instances, the spark ignition of the fireplace may

cause intermittent, non-damaging, interference during

the lighting sequence with a TV plugged into the same

circuit. It is recommended that the fireplace and TV use

different circuits to mitigate the interference potential.

If interference is occurring on the same circuit, the use

of surge protectors may help alleviate the interference.

Accessories Requirements

• This appliance may be used with a wall switch, wall

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies ap-

proved accessories should be done now to avoid re-

construction. Follow instructions that come with those

accessories.

• Hearth & Home Technologies recommends that Intel-

liFire

Touch wireless controls be used for their fea-

tures and functionality with the IntelliFire

Touch igni-

tion system

Electrical Information

Figure 8.1 Junction Box Detail

NOTICE: DO NOT

wire

110-120 VAC to wall switch.

Junction Box Installation

If the box is being wired from the

INSIDE

of the appliance:

• Remove the screw attaching the junction box/receptacle

to the outer shell, rotate the junction box inward to dis

engage it from the outer shell. See Figure 8.1.

• Pull the electrical wires from outside the appliance through

the opening into the valve compartment and secure wires

with a Romex connector. See Figure 8.1.

• Make all necessary wire connections to the junction box/

receptacle and reattach the junction box/receptacle to

the outer shell.

Electrical Service and Repair

WARNING! Risk of Shock!

Label all wires prior to dis-

connection when servicing controls. Wiring errors could

cause improper and dangerous operation. Verify proper

operation after servicing.

WARNING! Risk of Shock!

Replace damaged wire with

type 105º C rated wire. Wire must have high temperature

insulation.

14/2WG

Romex Connector

(Not Provided)

WHT

BLK

GRN wire

inside box

Copper

ground attached

to GRN screw with

GRN wire

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды

Majestic MERID36, Руководство по установке

Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды