Majestic MERID36 страница 42 Скачать руководство пользователя | Manualshive

Страница: 42 / 75

background image

42

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

E. Vertical Termination Requirements
Install Metal Roof Flashing

• See minimum vent heights for various pitched roofs

(Figure 7.12) to determine the length of pipe to extend

through the roof.

• Slide the roof flashing over the pipe sections extending

through the roof as shown in Figure 7.13.

Roof Pitch H (Min.) Ft.

Flat to 6/12........................................1.0*
Over 6/12 to 7/12 ............................1.25*
Over 7/12 to 8/12 ..............................1.5*
Over 8/12 to 9/12 ..............................2.0*
Over 9/12 to 10/12 ............................2.5*
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0

Figure 7.12 Minimum Height From Roof to Lowest Discharge

Opening

HORIZONTAL

OVERHANG

VERTICAL

WALL

GAS DIRECT VENT

TERMINATION CAP

12

X

ROOF PITCH

IS X/ 12

LOWEST

DISCHARGE

OPENING

2 FT.

MIN.

20 INCHES MIN.

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

Figure 7.14 insert Bolt into Brackets

NOTICE:

Failure to properly caulk the roof flashing and

pipe seams could permit entry of water.

• Caulk the gap between the roof flashing and the outside

diameter of the pipe.

• Caulk the perimeter of the flashing where it contacts the

roof surface. See Figure 7.13.

• Caulk the overlap seam of any exposed pipe sections

that are located above the roof line.

CAULK

Figure 7.13

Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during instal-

lation. Sheet metal edges are sharp.

• Slide the storm collar onto the exposed pipe section

and align brackets.

• Insert a bolt (provided) through the brackets and install

nut. Do not completely tighten.

• Slide the assembled storm collar down the pipe section

until it rests on the roof flashing (see Figure 7.14).

• Tighten nut and make sure the collar is tight against the

pipe section.

• Caulk around the top of the storm collar. See Figure 7.15.

* H minimum may vary depending on regional snowfall.

Refer to local codes.

«
...
40
41
42
43
44
...
»

Содержание MERID36












































































Отзывы:

Нет отзывов

Похожие инструкции для MERID36

Бренд: barkman Страницы: 16

Бренд: Paloform Страницы: 15

Kingsman Marquis MQVL48N

Бренд: R-Co Страницы: 80

Бренд: United States Stove Страницы: 4

Бренд: Vermont Castings Страницы: 14

Бренд: Lennox Страницы: 4

Бренд: Majestic Страницы: 48

Бренд: Amantii Страницы: 33

Бренд: Valor Страницы: 28

Бренд: Majestic Страницы: 26

Бренд: Enviro Страницы: 23

Бренд: Kenwood Страницы: 24

Бренд: Kenwood Страницы: 42

Бренд: Kenwood Страницы: 47

Бренд: IHP Страницы: 2

Superior Fireplaces Elite VRE4336ZEN

Бренд: IHP Страницы: 16

Crescent II Door

Бренд: Hearth and Home Technologies Страницы: 2

Бренд: Hearth and Home Technologies Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды