Majestic MERID36 страница 56 Скачать руководство пользователя

Страница: 56 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

E. Ember Placement

WARNING! Risk of Explosion!

Follow ember place-

ment instructions. DO NOT place ember directly over

burner ports. Replace ember material annually. Improp-

erly placed ember material interferes with proper burner

operation.

Place the Ember Material

See Figures 11.3. Place a small amount of 1/2 in. diam

eter pieces (dime-size) of ember material on the burner

top. Be careful not to cover burner ports. It is not neces

sary to use the entire bag. Save the remaining amount

for future use.

WARNING! Risk of Explosion!

Follow ember placement

instructions. DO NOT place embers directly over burner

ports. Replace ember material annually. Improperly placed

embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place

the ember material:

• Embers CANNOT be placed directly over ports. Care

should be taken not to cover the lighting trail of ports

(from back to front).

• Place dime-size pieces of Glowing Embers® just in front

of the port trail, but not on or in between the ports. See

Figure 11.3. Care should be taken so that the ports are

not covered. Failure to follow this procedure will likely

cause lighting and sooting problems.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated

inside the firebox or underneath in the control cavity.

Figure 11.3 Placement of Embers

= LAVA ROCK
= EMBERS

= NO EMBERS IN THIS AREA

D. Install Optional Glass or Fiber Refractory

Optional fiber or glass refractory kits are available for this

model. Follow the instructions supplied with the kit to in

stall the refractory.

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды

Majestic MERID36, Руководство по установке

Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды