Majestic MERID36 страница 41 Скачать руководство пользователя

Страница: 41 / 75

Majestic • MERID36IN, MERID36IL, MERID42IN, MERID42IL Installation Manual • 2517-980 Rev. C • 3/18

NOTICE:

When installing a vent system with an HRC

termination cap, all pipe system joints shall be sealed

using a high temperature silicone sealant (300 ºF minimum

continuous exposure rating).

•

Apply a bead of silicone sealant (300 ºF minimum

continuous exposure rating) inside the female outer pipe

joint prior to joining sections.

•

Only outer pipes are sealed, sealing the inner flue is not

required.

•

All unit collar, pipe, slip section, elbow and cap outer

flues shall be sealed.

120º

Figure 7.8 Securing Vertical Pipe Sections

120º

Figure 7.9 Securing Horizontal Pipe Sections

D. Disassemble Vent Sections

• Rotate either section (see Figure 7.10) so the seams on

both pipe sections are aligned as shown in Figure 7.11.

• Pull carefully to separate the pieces of pipe.

Figure 7.11 Align and Disassemble Vent Sections

Figure 7.10 Rotate Seams for Disassembly

C. Secure the Vent Sections

• Vertical runs originating off the top of the appliance, with

no offsets, must be supported every 8 ft. (2.44 m) after

the maximum allowed 25 ft. (7.62 m) of unsupported rise.

• Vertical runs originating off the rear of the appliance, or

after any elbow, must be supported every 8 ft. (2.44 m).

• Horizontal runs must be supported every 5 feet (1.52

m).

• Vent supports or plumbers strap (spaced 120º apart)

may be used to support vent sections. See Figures 7.8

and 7.9.

• Wall shield firestops may be used to provide horizontal

support to vent sections.

• SLP ceiling firestops have tabs that may be used to

provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support could allow vent to sag and separate.

Use vent run supports and connect vent sections per in-

stallation instructions.

DO NOT

allow vent to sag below

connection point to appliance.

Содержание MERID36












































































Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды

Majestic MERID36, Руководство по установке

Результаты поиска

Содержание MERID36

Отзывы:

Похожие инструкции для MERID36

Бренды по названию

Популярные бренды