MacDon R113 SP Скачать руководство пользователя страница 198

Страница: 198 / 240

215009

184

Revision A

1021092

Figure 4.177: Frame Attachment

–

Cross Section View

14. Install washer (A) onto bolt (B) and apply an anti-seize

compound to the bolt shank only. Do

NOT

apply anti-seize

to the threads.

15. Install bolt (B) with washers (C) as determined in Step

12,

page 183

16. Install three washers (D) and nut (E) onto bolt. Torque to

332

–

346 Nm (245

–

255 lbf·ft).

17. Repeat Step

12, page 183

to Step

16, page 184

for the

opposite side.

1021880

Figure 4.178: Center-Link Support

18. With flat washer shim (A) on both sides of the center-link

support, install securing bolt (B) and washer (C) through the
conditioner center-link support bracket and center-link
support.

19. Install nut (D) and torque to 332

–

346 Nm (245

–

255 lbf·ft).

1029832

Figure 4.179: Header on Blocks

WARNING

To prevent frame from slipping off forks, ensure frame is
secured to forks. Failure to do so could result in death or
serious injury.

20. Lift the header and remove wooden blocks (A) under the

skid shoes. Lower the header to the ground.

21. Remove any straps or chains securing the frame to the

forks, and back the forklift away from the work area.

MAINTENANCE AND SERVICING

Содержание R113 SP

















































































































































































































































Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды

MacDon R113 SP, Руководство оператора

Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды