MacDon R113 SP Скачать руководство пользователя страница 6

Страница: 6 / 240

Summary of Changes

The following list provides an account of major changes from the previous version of this document.

Section

Summary of Change

Internal Use

Only

Throughout manual

Removed R116 SP-specific content from book.

Tech Pubs

1.2 Signal Words, page 2

Added description for IMPORTANT and NOTE signal words
appearing throughout this manual.

Tech Pubs

2.3 Definitions, page 19

New definitions added: cab-forward, export header,
header, North American header, rpm, and windrower.

Tech Pubs

•

3.3.1 Engaging and Disengaging
Header Safety Props

–

M1240

Windrower, page 24

•

3.3.2 Engaging and Disengaging
Header Safety Props

–

M Series

Self-Propelled Windrower, page 25

Updated illustrations to show MY2020 safety props.

ECN 58047

3.4.1 Attaching R113 SP Rotary Disc
Header to M1 Series Windrowers, page 27

Updated illustrations to show MY2020 safety props.

ECN 58047

•

3.4.2 Attaching R113 SP to M155 or
M155E4 SP Windrowers

–

Hydraulic

Center-Link with Optional
Self-Alignment, page 32

•

3.4.3 Attaching R113 SP to M155 or
M155E4 SP Windrower

–

Hydraulic

Center-Link without Optional
Self-Alignment, page 37

Updated float linkage and safety prop illustrations.

ECN 58047

Connecting Header Hydraulics and
Electrical

–

M155 and M155E4 SP

Windrowers, page 45

Updated illustrations for hydraulic connections.

Tech Pubs

3.5 Detaching Header from M1240
Windrower, page 52

Updated illustrations to show MY2020 safety props.

ECN 58047

3.8.4 Ground Speed, page 70

Updated ground speed chart to only show R113 SP
headers.

Tech Pubs

3.9 Reconfiguring Cutterbar Crop Stream,
page 71

Updated cutterbar configuration illustration.

Tech Pubs

Positioning Rear Baffle

–

Roll Conditioner,

page 82

Updated illustration.

Tech Pubs

Positioning Rear Baffle Deflector Fins,
page 83

Updated illustration for deflector fins in field position.

Tech Pubs

4.3.1 Maintenance Schedule/Record, page
93

Updated maintenance intervals.

Tech Pubs

4.5 Cutterbar System, page 99

Updated cutterbar illustration.

Tech Pubs

Draining the Cutterbar, page 102

Updated illustration.

Tech Pubs

Inspecting Cutterbar Discs, page 104

Added steps to procedure.

Tech Pubs

215009

Revision A

Содержание R113 SP

















































































































































































































































Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды

MacDon R113 SP, Руководство оператора

Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды