MacDon R113 SP Скачать руководство пользователя страница 194

Страница: 194 / 240

215009

180

Revision A

1024821

Figure 4.165: Left Side of Conditioner

–

Right Side

Similar

12. Loosen two M16 hex head bolts (A) at each side of the

conditioner that secure it to the header.

1024878

Figure 4.166: Conditioner Gearbox

13. Loosen two carriage bolts (A) securing conditioner gearbox

support (B) to the header.

WARNING

To prevent the conditioner from falling backward, ensure lifting
chains are secure and tight. Failure to do so may result in death
or serious injury.

CAUTION

Stand clear when detaching frame as frame may shift when
bolts are removed.

14. Adjust the height of the forks to raise the conditioner

slightly. Remove the loosened bolts and retain hardware for
reinstallation.

1024879

Figure 4.167: Lifting Conditioner

WARNING

Ensure spreader bar is secured to the forks so that it cannot
slide off the forks or towards the header. Failure to do so could
result in death or serious injury.

15. Using the forklift, lift conditioner (A) off header (B). Avoid

contact between the top of the conditioner and center-link
anchor (C).

16. Move the frame away from the work area, set it on the

ground, and remove the chains securing the conditioner to
the spreader bar.

MAINTENANCE AND SERVICING

Содержание R113 SP

















































































































































































































































Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды

MacDon R113 SP, Руководство оператора

Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды