MacDon R113 SP Скачать руководство пользователя страница 53

Страница: 53 / 240

215009

Revision A

1008948

Figure 3.42: Ground Speed Lever

Use the following GSL functions to position the center-link
hook above the header attachment pin:

•

HEADER TILT UP (A) to retract the center-link

•

HEADER TILT DOWN (B) to extend the center-link

Stop engine, and remove key from ignition.

1029715

Figure 3.43: Hydraulic Center-Link

Push down on rod end of link cylinder (A) until hook (B)
engages and locks onto header pin.

IMPORTANT:

The hook release must be down to enable the self-locking
mechanism. If the release is open (up), manually push it
down after hook engages header pin.

10. Check that center-link (A) is locked onto the header by

pulling upward on rod end (B) of cylinder.

1008946

Figure 3.44: Ground Speed Lever

CAUTION

Check to be sure all bystanders have cleared the area.

11. Start the engine.

12. Press HEADER UP switch (A) to raise the header to

maximum height.

13. If one end of the header does

NOT

fully raise, rephase the

lift cylinders as follows:

Press and hold the HEADER UP switch until both
cylinders stop moving.

Continue to hold the switch for 3

–

4 seconds. Cylinders

are now phased.

NOTE:

It may be necessary to repeat this procedure if there is
air in the system.

OPERATION

Содержание R113 SP

















































































































































































































































Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды

MacDon R113 SP, Руководство оператора

Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды