manualshive.com logo in svg

MacDon R113 SP, Руководство оператора

Операторский мануал MacDon R113 SP доступен для бесплатного скачивания на нашем сайте. Этот руководство поможет Вам изучить правильную эксплуатацию вашего устройства и максимально использовать его возможности. Скачайте мануал сейчас на manualshive.com.

Поделиться
Скачать
background image

P

preseason servicing ................................................ 95

R

rear baffles

positioning on roll conditioner............................... 82

recommended settings

header .............................................................. 67

reference

conversion chart ............................................... 217
maintenance requirements ................................... 92
torque specifications ......................................... 209

rock guards

inspecting ........................................................ 129
installing inboard rock guards.............................. 131
installing outboard rock guards............................ 133
maintaining...................................................... 129
removing inboard rock guards ............................. 130
removing outboard rock guards ........................... 132

roll conditioners ..................................................... 73

deflectors .......................................................... 81
forming shields ................................................... 81
roll tension......................................................... 77
roll timing .......................................................... 78

roll gaps........................................................... 73

–

74

adjusting roll gap

polyurethane rolls............................................ 75
steel rolls........................................................ 76

roll tension ............................................................ 77

adjusting ........................................................... 77

roll timing ............................................................. 78

adjusting ........................................................... 78
checking ............................................................ 78

roll-type conditioning,

See

roll conditioners

rpm

definition........................................................... 19

S

SAE

definition........................................................... 19

safety ..................................................................... 1

daily start-up checks ............................................ 22
general safety....................................................... 3
header safety props............................................. 25
hydraulic safety .................................................... 6
maintenance safety ............................................... 5
noise levels .......................................................... 2
procedures ........................................................ 90
safety alert symbols............................................... 1
safety sign decals .................................................. 8

installing decals ................................................. 8
locations .......................................................... 9

signal words ......................................................... 2
understanding safety signs.................................... 11

screws

definition........................................................... 19

SDD

definition........................................................... 19

serial numbers

locations............................................................. vi
records............................................................... vi

servicing

maintenance and servicing ................................... 89
preparing for servicing ......................................... 89

shields

–

no conditioner......................................... 186

installing.......................................................... 187
removing ......................................................... 186

soft joints

definition........................................................... 19

specifications

header .............................................................. 15
torque specifications ......................................... 209

spindle shear pins................................................. 149

installing.......................................................... 154
removing ......................................................... 150

spindles

changing.......................................................... 109
installing.......................................................... 114
removing ......................................................... 111
rotating ........................................................... 109

start-up procedures

daily start-up check ............................................. 22

T

TFFT

definition........................................................... 19

topography ........................................................... 86
torque

definition........................................................... 19

torque angles

definition........................................................... 19

torque specifications ............................................. 209

metric bolt specifications.................................... 209

bolting into cast aluminum .............................. 211

O-ring boss (ORB) hydraulic fittings

–

adjustable ..... 212

O-ring boss (ORB) hydraulic fittings

–

non-

adjustable ...................................................... 214

O-ring face seal (ORFS) fittings............................. 215
tapered pipe thread fittings ................................ 216

torque-tension

definition........................................................... 19

transporting the header........................................... 88
troubleshooting

mechanical ...................................................... 205
performance .................................................... 201

INDEX

Содержание R113 SP

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R113 SP

Baileigh Industrial 1000568 Operator'S Manual preview
1000568
Бренд: Baileigh Industrial Страницы: 40
RASHA PROFESSIONAL Orbit Quick User Manual preview
Orbit
Бренд: RASHA PROFESSIONAL Страницы: 11
MADRIX LUNA Technical Manual & Quick Start Manual preview
LUNA
Бренд: MADRIX Страницы: 24
MADRIX LUNA Quick Start Manual preview
LUNA
Бренд: MADRIX Страницы: 28
Raven CR7 Update Manual preview
CR7
Бренд: Raven Страницы: 17
Campbell SC932A Product Manual preview
SC932A
Бренд: Campbell Страницы: 12
FarmTek Growers Supply 109722 Manual preview
Growers Supply 109722
Бренд: FarmTek Страницы: 9
ParaBody Parabody 805 User Manual preview
Parabody 805
Бренд: ParaBody Страницы: 6
ParaBody 821 User Manual preview
821
Бренд: ParaBody Страницы: 11
Yamaha CBX-D3 Owner'S Manual preview
CBX-D3
Бренд: Yamaha Страницы: 29
Accurate Technology VALIANT Owner'S Manual preview
VALIANT
Бренд: Accurate Technology Страницы: 10
Gage Bilt GB924 Original Instructions Manual preview
GB924
Бренд: Gage Bilt Страницы: 28
ZIEHL-ABEGG ZA top SM315.100A Original Operating Instructions preview
ZA top SM315.100A
Бренд: ZIEHL-ABEGG Страницы: 76
K-SPORT KSH025 Assembly Instruction preview
KSH025
Бренд: K-SPORT Страницы: 5
GCE Zen-O lite RS-00600 User Manual preview
Zen-O lite RS-00600
Бренд: GCE Страницы: 20
B. Braun Aesculap S4 Cervical Instructions For Use/Technical Description preview
Aesculap S4 Cervical
Бренд: B. Braun Страницы: 43
Enabling Technologies Dynamique Biski Owner'S Manual preview
Dynamique Biski
Бренд: Enabling Technologies Страницы: 44
Flex-A-Seal Style 58 Installation, Operation, Maintenance Manual preview
Style 58
Бренд: Flex-A-Seal Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды