MacDon R113 SP Скачать руководство пользователя страница 230

Страница: 230 / 240

215009

216

Revision A

Table 7.8

O-Ring Face Seal (ORFS) Hydraulic Fittings (continued)

SAE Dash Size

Thread Size (in.)

Tube O.D. (in.)

Torque Value

lbf·ft

-16

1 7/16

150

–

165

111

–

122

-20

1 11/16

1 1/4

205

–

226

151

–

167

-24

–

1 1/2

315

–

347

232

–

256

-32

2 1/2

510

–

561

376

–

414

7.1.6

Tapered Pipe Thread Fittings

Assemble pipe fittings as follows:

Check components to ensure that fitting and port threads are free of burrs, nicks, scratches, or any form of
contamination.

Apply pipe thread sealant (paste type) to external pipe threads.

Thread fitting into port until hand-tight.

Torque connector to appropriate torque angle. The turns from finger tight (TFFT) and flats from finger tight (FFFT)
values are shown in Table

7.9, page 216

. Make sure that tube end of a shaped connector (typically 45 degree or

90 degree) is aligned to receive incoming tube or hose assembly. Always finish alignment of fitting in tightening
direction. Never back off (loosen) pipe threaded connectors to achieve alignment.

Clean all residue and any excess thread conditioner with appropriate cleaner.

Assess final condition of fitting. Pay special attention to possibility of cracks to port opening.

Mark final position of fitting. If a fitting leaks, disassemble fitting and check for damage.

NOTE:

Overtorque failure of fittings may not be evident until fittings are disassembled.

Table 7.9 Hydraulic Fitting Pipe Thread

Tapered Pipe Thread Size

Recommended TFFT

Recommended FFFT

1/8

–

1/4

–

3/8

–

1/2

–

3/4

–

1.5

–

2.5

–

11 1/2

1.5

–

2.5

–

1 1/4

–

11 1/2

1.5

–

2.5

–

1 1/2

–

11 1/2

1.5

–

2.5

–

11 1/2

1.5

–

2.5

–

REFERENCE

11. Torque values and angles shown are based on lubricated connection as in reassembly.

Содержание R113 SP

















































































































































































































































Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды

MacDon R113 SP, Руководство оператора

Результаты поиска

Содержание R113 SP

Отзывы:

Похожие инструкции для R113 SP

Бренды по названию

Популярные бренды