Lynx SMART30, Руководство пользователя

Страница: 31 / 48

Do you have the correct opera ng system on your smart
device?
iPhone 5, 5C, 6, or newer, iPad version 2.0 or newer or
Android 4.4 opera ng system or newer
To fi nd your opera ng system on your smart device:
iPhone and iPad : Go to Se ngs /General/ About/ Phone to
fi nd your model number
Android : Go to Se ngs, About Phone, Android version
Then, make sure that your wireless network is connected
properly and is broadcas ng at least a 60% signal to
reach your grill. A er that, proceed through the wireless
connec on sequence:
Refer to the quick start guide for details.
TROUBLESHOOTING YOUR SMARTGRILL BY LYNX™... con nued

The four digit PIN can be located on the ra ng plate. This is
your personal number that insures that no version of the
SmartGrill by Lynx™ app save yours is able to control your
SmartGrill by Lynx™.

Input the SmartGrill by Lynx™’s Serial Number. This serial
number can be found on the last page of this Care & Use
manual or on the underside of the drip tray on the
SmartGrill by Lynx™.
If needed, the Wi ‐ Fi se ng in your grill can be reset. Press the
power bu on to turn the grill o ff . Then press and hold the
Power bu on in the OFF posi on for 15 seconds.
If a factory reset is done, you will have to setup your Wi ‐ Fi
connec on again. Please refer to the Quick Start Guide for
setup procedure.
First, con fi rm that the grill is ge ng electricity by checking the
lights that surround the dials on the front panel of your Smart ‐
Grill by Lynx™.
Check the Burners
If your burner fails to ignite, SmartGrill will text or say
"Burner <N> has no fl ame." If the burner has no fl ame,
SmartGrill will turn o ff the gas to that burner.
Be careful! If the burner fails to ignite, wait fi ve minutes
before a emp ng to ignite other burners!
Check to make sure your gas line is connected and the
shut o ff valve is turned on. Re ‐ check fuel connec ons for
leaks and ensure the supply is of the correct type and is of
adequate pressure. (See INDEX: “Leak Test Procedure” for
further details.)
If you know you are ge ng gas, wait for any gas to
dissipate and remove the burner and check for gas
blockages.
Replace any damaged supply lines.
Check the regulator
the regulator and hose assembly is the one designed for
and supplied with your Lynx grill and that it is correctly
set up for the type of fuel you are using. (See INDEX:
“Regulator Conversion” for further details.)
The hose and regulator provided by Lynx Grills must be
used if your grill is set up for use with a liquid propane gas
cylinder.
Check that there is no physical pressure being applied to
the regulator a ached to the back of the grill. The
regulator contains a fl exible diaphragm and should not
be allowed to touch the grill body or its surroundings.
Check for obstruc ons
Ensure that the burners and the drip tray are clean and
free from obstruc ons.
FACTORY RESET
GRILL WILL NOT LIGHT
Check the Igniters
Your Lynx SmartGrill by Lynx™ uses an electric igni on
system that does not spark. Instead the igniters will glow
constantly when a control knob is turned on. If one of your
igniters is not working, SmartGrill will say or send you a
text of "Igniter Failure".
Ensure that all burners are set to OFF
Remove a cooking grate so you can clearly see the igniter.
Turn the burner knob ON (two full rota ons clockwise) and
wait approximately one minute for the igniter to glow.
Check all igniters. If they do not glow, call Lynx for service
at 888 ‐ 289 ‐ 5969.