Step by Step instructions for GRAFIK Eye Dimming Panel
20
Set Normal/
Emergency Switch
Circuit Selector in Normal
(Non-Essential) Panel
Circuit Selector in
Emergency (Essential)
Lighting Panel
STEP 17: Set Normal/Emergency Switch (Non-
Essential/Essential)
Note:
This step is only performed if there are any panels with
Emergency (Essential) Lighting Circuits on the job.
Panels are shipped with Switch 6 (located at the base of each Circuit
Selector) in the center position for operation without any Emergency
(Essential) Lighting Circuits.
Identify a panel supplied with Normal (Non-Essential) power. Move
its Switch 6 to the left position.
For all the Emergency (Essential) Lighting Panels, move Switch 6 to
the right position.
In this arrangement, the Emergency (Essential) Lighting Panel will
“sense” the Normal (Non-Essential) Panel’s power. When Normal
(Non-Essential) power is removed, the Emergency (Essential)
Lighting will go to ‘ord’ override levels (factory set to 100%).
Loss of Normal (Non-Essential) power can be simulated by turning
off all connected Normal (Non-Essential) Panel’s Control Breakers.
When Switch 6 is in its center position (as shipped), terminal 5 has
no affect on the Circuit Selector operation.
Notes
:
■
If there is no Normal Panel, a PS-CIP can be used to create an
external ‘sense’ line. See Lutron.
■
Override (‘ord’) Level is factory set to full output (100). If less
than full output is needed, contact Lutron.
Data A OK
Data B OK
Power
1 2 3 4
5
D
C
D
Load Type
High-End Trim
Circuit Level
Low-End Trim
5
4
3
Value
Link A
Link B
2
1
Circuit
A B
Common
24VFW
MUX
MUX
Dr
ain
Sense
Comm
Dr
ain
MUX
MUX
C
1 2 3 4
D
5
D
Link Link
Read instructions before setting the
Load Type. Instructions show more load types.
1-1
2-1
2-2
3-1
4-1
Incandescent
Fluorescent Lutron Hi-lume FDB Ballast
Neon / CC
Non-Dim
---
Unassigned
Fluorescent Lutron Tu-Wire Ballast
TM
('Ad' Displayed)
Address
Zone Assignment
w/ Circuit Schedule
Zone Assignment
TM
w/
Zone Capture
Warning -
(See Instructions)
Load Type Quick Reference:
S
ELECT
C
IRCUIT
S
ELECT
V
ALUE
V
IEW
V
ALUE
S
ELECT
V
ALUE
D
ISPLAYED
Data A OK
Data B OK
Power
1 2 3 4
5
D
C
D
Load Type
High-End Trim
Circuit Level
Low-End Trim
5
4
3
Value
Link A
Link B
2
1
Circuit
A B
Common
24VFW
MUX
MUX
Dr
ain
Sense
Comm
Dr
ain
MUX
MUX
C
1 2 3 4
D
5
D
Link Link
Read instructions before setting the
Load Type. Instructions show more load types.
1-1
2-1
2-2
3-1
4-1
Incandescent
Fluorescent Lutron Hi-lume FDB Ballast
Neon / CC
Non-Dim
---
Unassigned
Fluorescent Lutron Tu-Wire Ballast
TM
('Ad' Displayed)
Address
Zone Assignment
w/ Circuit Schedule
Zone Assignment
TM
w/
Zone Capture
Warning -
(See Instructions)
Load Type Quick Reference:
S
ELECT
C
IRCUIT
S
ELECT
V
ALUE
V
IEW
V
ALUE
S
ELECT
V
ALUE
D
ISPLAYED
SW6
SW6
Move left
Move right
