manualshive.com logo in svg

LTV G-187, Инструкция, Страница: 20 / 75

Поделиться
Скачать
LTV G-187 Скачать руководство пользователя страница 20

 

20

 b. FUNCTION SWITCH IN 200 Kc AM POSITION, MASTER IF CHANNEL 

 The first two high-gain 6DC6 remote cutoff amplifiers (V-501, V-502) receive an AGC 

voltage developed at the grid of the 6AK5 (V-504) AM detector. The third IF amplifier (V-

503) which drives the AM detector is not gain controlled but its signal handling capabilities 

have been improved by increasing the screen voltage.   A self-resonant choke is connected in 

the AM output lead from the 6AK5 AM detector (V-504) to prevent IF signals from leaving 

the IF subassembly. 

With the AGC switch in the manual position the AGC voltage is shorted to ground, and the IF 

gain control in the cathode circuit of the two 6DC6 IF amplifiers is unshorted and becomes 

operative. The gain-controlled stages use cathode compensation of input capacity variation 

with bias change. The zero center tuning meter operates only in the FM position.  Correct 

tuning of an AM signal may be accomplished by first tuning in the signal with the selector 

switch in the FM position and then switching to the AM

 

200kc position. 

c. FUNCTION SWITCH IN 200 Kc FM OR AM POSITION, SLAVE IF CHANNEL 

 Also the “Slave” 21.54 Mc IF channel has two high-gain stages (V-301, V-302) using 6DC6 

remote cutoff amplifiers that can receive an AGC voltage  The third IF amplifier (V-303) 

drives a solid-state AM detector (CR-301) whose output is used for various purposes (AGC, 

signal strength meter M-101, direction finding) . 

The M-101 meter has a logarithmic characteristic and it is not calibrated, though it may be 

used for a relative indication of signal strength. 

d. FUNCTION SWITCH IN 40 Kc FM POSITION, MASTER IF CHANNEL 

 Plate and screen voltage are removed from both the channels of the 21.4 Mc IF amplifier 

subchassis  and a 21.4 Mc signal is coupled from T-602 to the grid of V-606 (6CW4), that 

together with V-607 (6CW4)  forms a 2.5 Mc cascode mixer.  V-608 (6CW4) is the 18.9 Mc 

crystal controlled 2nd conversion oscillator, that  is capacitively coupled to the above 

mentioned cascode circuit. 

The output of the 2.5 Mc mixer is coupled to V-609 (7587), a 2.5 Mc amplifier, and then is 

fed to V-610 (7587) through L-606 and L-607, which, together, comprise a 2.5 Mc double-

tuned 40 Kc. Pass-Band filter. 

Содержание G-187












































































Отзывы:

Нет отзывов