10. Remote telephone operation
User can dial telephone number of the control panel perform the operations:
arm away/stay, disarm spot supervision and hearing alarm types.
Dial telephone number of the control panel for more than ringing attempts
set. The system will answer automatically and announce the user with a
voice 'Di'. Then user presses '# + 4 digits password(user password operation
password) + 1 operation digit + #', the control panel will operate
corresponding commands. 6 operation digits, 1 means arm-away, 2 means
arm-stay, 3 means disarm,4 means spot supervision, 5 means hearing
current alarm voices, 0 means hang-up / stop dialing to alarm.
For example, user password is 1234. To disarm the control panel, user can
press '# 1 2 3 4 3 #' after switching on the system. If the operations is
correct, 'Di' will be heard once. If the operations is incorrect, 'Di' will be heard
twice. If password is wrong, user can input password and operate digit again
5.2.2 Bell output terminals
The maximal drive capacity of bell terminal (+BELL -) is 400mA /12VDC
Connect the two power lines of the bell to 'BELL+' and 'BELL-' terminals
When the system is powered up and initialized bell will chirp once,
indicating it works normally .Setting the bell on/off and the chirping time
can be programable with software
5.2.3 Wired zone connection
Each loop is connected to an end-of-line (EOL) resistor. For different
detectors, modes of connection are shown as followed:
When connecting N.C. detector, connection mode:
without inputting '#' in advance. The control panel will hang up if password is
input incorrectly three times or user does not press any key in 30 seconds
during the operations.
When alarming, the control panel dial user telephone, if there is no voice
Zone
N.C. Detector
after receiving the telephone or user unwilling to wait, pressing any key (key
'5' recommended), the control panel will play voice information immediately.
Alarm information order is user address record then the alarm type voice.
The system will circulate play the alarm voice information.
Note: 1.Do not press any keys during voices 'Di' or messages can not be
received correctly. Do not press any key when the system is in voice alarm
status. 2.If user hang up the telephone without any operation the control
panel will dial user telephone repeatedly.
10.1 Telephone disarm
After picking up the telephone press '# + 4digits password(user
password, operation password) + 3 + # ' to disarm, for example, if user
password is 1234, press '#12343#'.
When the control panel dials to alarm, user can press 3 to disarm after
hearing alarm voice.
10.2 Telephone arm-away
After picking up the telephone, press '# +4digits password(user
password, operation password) + 1 + #' to arm, When alarm occurs, user
has to disarm first and then arm the system again. For example, if user
password is 1234, press '#12343#' and then press '1#' to arm after
hearing prompt voices.
When the control panel dials to alarm, user can press 3 to disarm and
then press 1 to arm after hearing alarm voice.
-28-
G
Figure 5 N.C. Detector
When connecting N.O. detector, connection mode:
Zone
N.O. Detector
G
Figure 6 N.O. Detector
5.2.4 Telephone line connection
Connect telephone line to 'LINE_IN' interface of the control panel
(Refer to the figure 3)
Connect telephone or facsimile machine to 'LINE_OUT' interface of the
controller panel, ensuring no effect on telephone(Refer to the figure 3)
Under the telephone line monitoring status, the control panel will alarm
when the telephone line trouble. 'T' flashes per second in lower right
corner of LCD, buzzer chirps for 1 minute. After disarmed buzzer off and
'T' flashes on LCD
-5-
