background image

Operating instructions AirLED Polisher 

28

6.5.  How to operate with AirLED Polisher

A short learning period is required by the user, as with any new technique, until the ideal angulations, soft tissue 
protection and an effective treatment can be achieved.

WARNING

PERSONAL INJURY HAZARD! Patients suffering from chronic respiratory 

disease like bronchitis or asthma must not, under any circumstances, be treated 

with an air polishing device. The jet of air and powder could cause respiratory 

difficulties.

WARNING

PERSONAL INJURY HAZARD! - GLYCINE

•  Predisposed persons may be sensitive to glycine. If allergic reactions are 

observed, stop using the product and completely remove the powder from 
patiens mouth. 

•  The treatment of deep periodontal pockets cause bacteraemia. Please 

apply appropriate restrictions for the treatment of risk patient’s (general 
weakened immunity, endocarditis).

•  Do not direct the jet powder towards fillings, crowns or bridgework as this 

could damage these restorations.

WARNING

PERSONAL INJURY HAZARD! - SODIUM BICARBONATE

•  Do not perform Sodium Bicarbonate polishing treatment for patients who: 

•  have a renal insufficiency
•  are on sodium restricted diet
•  have allergic reactions to flavour containing powders 

(Use neutral powder instead.)

•  are on a long term steroid or diuretic therapy.

•  Do not direct the jet powder towards filling, crowns or bridgework as this 

could damage these restorations.

•  Do not direct the Sodium Bicarbonate spray onto the gingival sulcus 

or onto the gingival margin. Spray may cause unnecessary abrasion of 
the gingival tissues and / or extension of the periodontal pocketing with 
associated clinical complications.

WARNING

PERSONAL INJURY HAZARD! - CALCIUM CARBONATE 

•  Do not perform Calcium Bicarbonate polishing treatment for patients who: 

•  have allergic reactions to components of the powder.
•  have a disease or condition that may lead to hypercalcemia.

•  Do not direct the jet powder towards filling, crowns or bridgework as this 

could damage these restorations.

•  Do not direct the Calcium Carbonate spray onto the gingival sulcus or onto 

the gingival margin. Spray may cause unnecessary abrasion of the gingival 
tissues and / or extension of the periodontal pocketing with associated 
clinical complications.

Содержание LM-ProPower CombiLED













































Отзывы: