manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, Руководство пользователя

Поделиться
Скачать
LM-Dental LM-ProPower CombiLED Скачать руководство пользователя страница 25

Operating instructions AirLED Polisher 

25

6.  OPERATING INSTRUCTIONS AIRLED POLISHER 

Indications for polishing:

•  Biofilm removal and dissolution.
•  To clean teeth prior to bleaching.
•  To clean pits and fissures prior to sealant placement.
•  To clean surfaces prior to any acid etch or bonding procedure. 
•  To clean orthodontically banded or bracketed teeth. 
•  Biofilm removal in implant maintenance therapy.

For optimal performance, use original LM-ProPower air polishing powders.

6.1.  How to install AirLED Polisher to use

PREPARATIONS (BOTTLE VERSION)

1.  Fill the medicament bottle with water or with approved medicament solution. Refer to the approved 

medicament solutions, See instructions “3.8. Medicament bottle (optional)” on page 14. 

2.  Turn the bottle cap onto the bottle and push it onto the connector. 
3.  Make sure that the unit is connected to the air supply, the power cable is connected and the unit is in 

standby mode, the green indicator lamp is illuminated.

NOTICE!

Tighten the powder container fully before activating the polisher.

NOTICE!

Do not activate the polisher before nozzle is installed.

Содержание LM-ProPower CombiLED













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды