manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, Руководство пользователя

Поделиться
Скачать
LM-Dental LM-ProPower CombiLED Скачать руководство пользователя страница 18

Taking CombiLED in to use

18

4.2.  How to connect the unit to the air supply

NOTICE!

Use only dry and filtered compressed air.

NOTICE!

Special skills required. Consult an approved technician to connect the unit to 

the air supply.

1.  Set the air supply OFF.
2.  Verify that the air pressure obeys to the data in the 

technical data section. See instructions “9. Technical 
data” on page 39 

3.  Use only dry and filtered compressed air. 
4.  Push the hose onto the quick connect coupling.
5.  Connect the other end of the hose to the air supply.
6.  Set the air supply ON.
7.  To disconnect, push orange ring and pull tubing out 

when orange ring still is pushed in.

4.3.  How to connect the unit for tap water (optional) 

NOTICE!

Special skills required. Consult an approved technician to connect the unit to 

the water supply.

1.  Set the water supply OFF.
2.  Verify that the water pressure obeys to the data 

in the Technical data section. See instructions “9. 
Technical data” on page 39

3.  Verify that the water supply fulfils the medical 

demands of hygiene.

4.  Push the hose onto the quick connect coupling.
5.  Connect the other end of the hose to the water 

supply.

6.  Set the water supply ON.
7.  To disconnect, push orange ring and pull tubing out 

when orange ring still is pushed in.

Содержание LM-ProPower CombiLED













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды