manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, Руководство пользователя

Поделиться
Скачать
LM-Dental LM-ProPower CombiLED Скачать руководство пользователя страница 39

Technical data

39

9.  TECHNICAL DATA

Manufacturer

LM-Instruments Oy, PL 88 (Norrbyn rantatie 8) FI-21601 Parainen, 
Finland

Model

LM-ProPower CombiLED

Classification

EN60601-1: Class 1, Type B
93/42/EEC: Medical products, class IIa

L x W x H

270 x 110 x 165 mm (without bottle and powder container)

Weight

3400 g

Voltage

100 Vac, 50-60 Hz
115 Vac, 50-60 Hz
230 Vac, 50-60 Hz

Primary fuse

T500 mA, 250 V, Ø5x20 mm (100 Vac)
T400 mA, 250 V, Ø5x20 mm (115 Vac)
T200 mA, 250 V, Ø5x20 mm (230 Vac)

Power cable

Separate with protective earth plug

Power consumption

Max. 40 VA

Scaler power consumption

Max. 24 VA

Scaler power output

Max. 10 W (24 kHz - 28 kHz, automatic tuning)

Ambient temperature

Transport and storage -40°C to 70°C (-40°F to 158°F)
Operation 10°C to 40°C (50°F to 104°F)

Relative humidity

Transport and storage 10% to 100%
Operation 10% to 95%

Water supply pressure (version 
conn. to tap water)

1 - 10 bar (0.1–1,0 MPa, 14.5–145 PSI)

Water consumption

10 - 50 ml/min

Bottle volume (bottle version)

500 ml

Air supply pressure

4 - 10 bar (0.4 - 1.0 MPa, 58 - 145 PSI) Use only dry and filtered 
compressed air.

Air consumption

Max. 20 l/min

Powder container capacity

40 g

Содержание LM-ProPower CombiLED













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды