manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, Руководство пользователя

Поделиться
Скачать
LM-Dental LM-ProPower CombiLED Скачать руководство пользователя страница 42

Warranty 

42

10.3. Installation check-list

Task

Description

OK

Initials

Date

Visual check

Delivery packing was undamaged

Content of the 
delivery

All the devices and part were according to the 
section “3. Content of delivery” on page 11“

Visual check

All the parts were intact

Mains connection

Mains supply is in compliance with back panel label 
information (picture in section 3.7)  voltage:_____ V, 
___Hz

Air supply

Air pressure ____is according to specification 4-10 
bar (0.4 – 1.0 MPa).
Compressed air is dry and medical grade
Air connection is close-knit and no indications of 
leakage is seen or heard

Water supply (bottle 
model)

Bottle filled with clean water, and bottle in 
place according to instructions in section “3.8. 
Medicament bottle (optional)” on page 14

Water supply (tap 
water model)

Tap water pressure is ____, and according to the 
specification 1-10 bar (0.1 – 1.0 MPa).
Water connection is close-knit and no indications of 
leakage is seen or heard

Foot control

Cable connected to the main unit

Powder container

Filled with LM-ProPower powder and connected to 
mains unit according to the instructions in section 
“6.1. How to install AirLED Polisher to use” on page 
25.

Polisher handpiece

ErgoGrip and nozzle assembled according to the 
instructions in section “6.1. How to install AirLED 
Polisher to use” on page 25.

Scaler handpiece

ErgoGrip and tip assembled according to the 
instructions in section “5.1. How to install UltraLED 
Scaler to use” on page 20.

Instrument assembly is now ready for the operational test.

Содержание LM-ProPower CombiLED













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды