manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, Руководство пользователя

Поделиться
Скачать
LM-Dental LM-ProPower CombiLED Скачать руководство пользователя страница 5

Introduction

5

1.  INTRODUCTION

Foreword

This is user manual for CombiLED product. Read and understand this manual before you use the product. If 
there are any questions regarding the contents of this manual, please contact LM-Instruments Oy. Keep User 
manual in place where it is easily available for all users.

General Requirements

Special precautions are necessary to this product regarding EMC (Electro Magnetic compatibility). It is necessary 
to install the product and put it into servicing referred to the EMC data in chapter “2.6. EMC Guidance and 
manufacturer’s declaration” on page 8.  
Portable and mobile RF (Radio Frequency) communications equipment can have an unwanted effect on the 
product. 
Connect the product to electricity-, water- and compressed air supply which obeys the requirements in the 
Technical data.

Servicing

Only approved service persons are permitted to do servicing to this product. The maintenance procedures 
which are introduced in this manual are for the user. User must obey the maintenance measures to keep safe 
and efficient operation of the product.

Содержание LM-ProPower CombiLED













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды