manualshive.com logo in svg

LM-Dental LM-ProPower CombiLED, Руководство пользователя

Поделиться
Скачать
LM-Dental LM-ProPower CombiLED Скачать руководство пользователя страница 30

Cleaning and maintenance

30

7.  CLEANING AND MAINTENANCE

NOTICE!

Immediately after using any type of medicament in the medicament bottle, run 

the automatic cleaning cycle with clean water in the medicament bottle for both 

the scaler and the polisher until clean water comes out of the handpieces.

Before cleaning and sterilizing, open water flow fully 
open of the scaler handpiece and the polisher  
(see images).

7.1.  Air purge quick cleaning function

With the polisher mode active, a press on the C key will air purge the handpiece for some seconds. Air purge 
the handpiece after each treatment to prevent clogging.

7.2.  Automatic cleaning function for the scaler and polisher

NOTICE!

The automatic cleaning function must always be performed with the polisher 

nozzle installed in the handpiece.

1.  Set OFF the scaler or polisher by pressing the “S” or “P” key for 3 seconds. The blue function indicator 

sets off.

2.  Open the water control completely.
3.  Put the scaler and/or the polisher handpiece above the cuspidor bowl.
4.  Press first the cleaning key “C” and then the “S” and/or “P” key.
5.  The cleaning cycle starts and stops automatically after 80 seconds. 

Содержание LM-ProPower CombiLED













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды