Lighthouse NanoCount 30+ Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 94

background image

Lighthouse NanoCount 30+ Operating Manual

1-2

248083427-1 Rev 4

WARNING:

The use of controls, adjustments or procedures

other than those specified within this manual may result in
personal injury and/or damage to this instrument. Attempts
by untrained personnel to disassemble, alter, modify or
adjust the electronics or optics may result in personal injury
and damage to the instrument and will void its warranty.

There are no user-serviceable components inside the
particle counter. Only factory authorized service personnel
should repair or service this instrument and its optical
system.

If replacement of the AC power cord is required, replace
with a power cord having as good as or better ratings than
the item as provided by Lighthouse Worldwide Solutions.
Attempting to use an under-rated power cord can expose
the instrument power supply, adjacent equipment or the
user to dangerous shock and fire hazards. Failure to heed
this warning can result in personal injury or death.

Figure 1-1 NC30+

Power Input Connector

Electrostatic
Safety
Information

Electrostatic discharge (ESD) can damage or destroy electronic
components. Therefore, any service or maintenance work should be
done at a static-free work station. A static-free work station requires an
ESD consultant to evaluate the work environment and propose the
equipment and apparel needed for a work station to be successful.

«
...
12
13
14
15
16
...
»

Содержание NanoCount 30+































































































Отзывы:

Нет отзывов

Похожие инструкции для NanoCount 30+

Бренд: Nautilus Hyosung Страницы: 38

Бренд: Nautilus Hyosung Страницы: 27

Бренд: Keithley Страницы: 134

Бренд: VeriFone Страницы: 28

currenza MB-US88-4.05C

Бренд: Crane Страницы: 2

Бренд: Derovis Страницы: 17

Бренд: Hameg Страницы: 36

Бренд: QUORION Страницы: 55

Бренд: Olivetti Страницы: 45

Бренд: netvox Страницы: 13

Бренд: Sharp Страницы: 144

Бренд: Sam4s Страницы: 7

Бренд: Met One Instruments Страницы: 41

Shelleymatic SH2C-74-NU

Бренд: Delfield Страницы: 16

Shelleysteel SCS-30

Бренд: Delfield Страницы: 28

Бренд: CashConcepts Страницы: 2

Бренд: CashConcepts Страницы: 9

Бренд: CashConcepts Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды