Lighthouse NanoCount 30+ Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 94

background image

00

248083427-1 Rev 4

1-1

1

General Safety

S

afety

Considerations

Warnings and cautions are used throughout this manual and the reader
should become familiar with the meaning of a warning before
operating the particle counter. Most warnings will appear in the left
margin of the page next to the subject or step to which it applies. Take
care when performing any procedures preceded by or containing a
warning. The classifications of warnings are defined as follows:

WARNING:

There are

no user-serviceable
components inside the
particle counter.

•

LASER - pertaining to exposure to visible or invisible LASER
radiation

•

Electrostatic - pertaining to electrostatic discharge

•

Network Connect - pertaining to communication ports and
instrument damage

LASER Safety
Information

This product is considered to be a Class 1 LASER product (as defined
by FDA 21 CFR, §1040.10) when used under normal operation and
maintenance. Performing service on the internal sensor can, however,
result in exposure to invisible radiation.

WARNING:

The use

of controls, adjustments
or procedures other than
those specified within
this manual may result in
personal injury and/or
damage to this
instrument.

The particle counter has been evaluated and tested in accordance with
EN 61010-1:2012, “Safety Requirements For Electrical Equipment for
Measurement, Control and Laboratory Use” and IEC 60825-1:2007,
“Safety of LASER Products”.

For further technical assistance, contact our Technical Support Team at
1-800-945-5905 (USA Toll Free), 1-541-770-5905 (Outside of USA).

«
...
11
12
13
14
15
...
»

Содержание NanoCount 30+































































































Отзывы:

Нет отзывов

Похожие инструкции для NanoCount 30+

Бренд: Nautilus Hyosung Страницы: 23

Бренд: Kluizen Страницы: 11

Бренд: Casio Страницы: 11

PHYSICS 1003122

Бренд: 3B SCIENTIFIC Страницы: 8

Бренд: YASKAWA Страницы: 53

Бренд: Magner Страницы: 18

Бренд: AccuBANKER Страницы: 19

Бренд: AccuBANKER Страницы: 40

Бренд: TEC Страницы: 130

Бренд: netvox Страницы: 9

Бренд: ACLAS Страницы: 6

Бренд: True Страницы: 2

Бренд: socomec Страницы: 46

Бренд: Hamilton Manufacturing Corporation Страницы: 26

Бренд: Opkon Страницы: 4

Бренд: ATO Страницы: 6

Бренд: Casio Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды