Lighthouse NanoCount 30+ Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 94

background image

Lighthouse NanoCount 30+ Operating Manual

4-14

248083427-1 Rev 4

Definitions of
Terms Used

This list is provided for the convenience of the user or technician.

•

ARP - Address Resolution Protocol, a program that can change
the ARP Cache of a host by adding or removing IP addresses.
Each IP address is associated to a MAC address.

•

ARP Cache - List of IP addresses and their associated MAC
addresses for hosts whose addresses cannot be resolved normally.

•

DHCP - Dynamic Host Configuration Protocol, a program
running on a server that issues IP addresses to computers or
devices (Hosts) on its LAN.

•

Gateway - a network device that controls traffic between two or
more networks.

•

Hardware address - a unique identifying code programmed by the
factory into a network device, such as a network PCB, comprised
of six two-digit groups of letters A-F and numbers 0-9.

•

Host - a computer or device that allows access to itself via a LAN.

•

IP (Internet Protocol) Address - a unique logical address used to
identify a host on a TCP/IP network.

•

LAN - Local Area Network, a group of computers or hosts
connected together in a relatively small geographical area, such
as a building or floor of a building.

•

MAC address - the same as hardware address.

•

Netmask - a logical hexadecimal number that prevents accessing
hosts outside of its range. A bit value of zero allows access and a
non-zero blocks access.

•

Subnet - a logical grouping of hosts based on their IP addresses.

•

TCP/IP - a communication protocol suite that is used for the
Internet and a large number of LANs that allows hosts to share
data.

•

Telnet - a communication program used primarily to issue
commands directly to a TCP/IP-based host.

«
...
44
45
46
47
48
...
»

Содержание NanoCount 30+































































































Отзывы:

Нет отзывов

Похожие инструкции для NanoCount 30+

Euro-150TE Flexy F

Бренд: ELCOM Страницы: 88

Бренд: Safescan Страницы: 10

Бренд: Safescan Страницы: 24

Бренд: Safescan Страницы: 56

Бренд: CUMMINS ALLISON Страницы: 17

EnergyCam 2.0 Open Wire

Бренд: Fast Forward Страницы: 2

Бренд: ACECO Страницы: 5

Бренд: Uniwell Страницы: 67

Бренд: Sam4s Страницы: 95

Бренд: Samsung Страницы: 83

Бренд: Magner Страницы: 66

Бренд: Met One Instruments Страницы: 32

Бренд: Olivetti Страницы: 58

Бренд: TSUJI ELECTRONICS Страницы: 43

Бренд: MZ electronic Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды