Lighthouse NanoCount 30+ Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 94

background image

Lighthouse NanoCount 30+ Operating Manual

4-16

248083427-1 Rev 4

Configure
Device

Ethernet Port Configuration

This section is organized based on the cable used to perform the
NC30+ programming.

Straight-through Cat5 requires a hub or switch and two straight-through
Cat5 cables. Cross-over Cat5 connects the PC directly to the NC30+
with no hub. Each will be explained separately. If troubleshooting is
required, the cross-over cable technique is easier to use in the field
because it requires fewer devices.

It cannot be stressed enough, however, that the instrument and PC be
configured using the same IP scheme (IP range, Default Gateway and
Netmask).

For troubleshooting outside of the LAN, it is suggested that the PC’s IP
address be used as the Default Gateway for both the PC and the
NC30+.

Frequently, it is necessary to change the NC30+ Ethernet parameters to
allow for easier troubleshooting. When this is needed, verify the
instrument is reprogrammed to its previous network settings before
reattaching to the LAN. Contact Lighthouse Technical Support at 800-
945-5905 (USA Toll Free), 541-770-5905 (Outside of USA) or the
network administrator for additional information.

Straight-through Cat5 Setup:

Note:

Screens shown

are examples only. Data
displayed and command
responses may differ.

This section requires the PC, two straight-through Cat5 cables and the
hub or switch.

1.

Connect one end of a straight-through Cat5 cable to the NC30+’s
Ethernet Port.

2.

The other end of the Cat5 cable should plug into one port on the
hub or switch.

3.

Attach another straight-through cable to the PC’s RJ45 receptacle
and an open port on the hub or switch.

4.

Proceed to “Windows Telnet Programming:” on page 4-17.

«
...
46
47
48
49
50
...
»

Содержание NanoCount 30+































































































Отзывы:

Нет отзывов

Похожие инструкции для NanoCount 30+

Бренд: Olivetti Страницы: 64

Бренд: DR. JOHANNES HEIDENHAIN Страницы: 29

Бренд: IRIS Страницы: 30

Бренд: CET Страницы: 8

Бренд: HP Страницы: 48

Бренд: DIEBOLD NIXDORF Страницы: 77

Бренд: POSIFLEX Страницы: 10

Бренд: POSIFLEX Страницы: 9

Бренд: PAX Страницы: 63

Бренд: Uniwell Страницы: 82

Бренд: Hach Страницы: 80

Бренд: Safescan Страницы: 24

Бренд: JCM Страницы: 191

Бренд: QUORION Страницы: 4

Бренд: CashConcepts Страницы: 16

Бренд: RCH Страницы: 70

Бренд: Sen Source Страницы: 11

Бренд: SEMTOM Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды