Lighthouse NanoCount 30+ Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 94

background image

Getting Started

248083427-1 Rev 4

3-13

Power

The NanoCount 30+ uses an IEC power cord for 100-240 VAC power.

Attaching the
Sensor Lines

This section provides instructions on how to attach the liquid source
and drain lines to the Inlet and Outlet nozzles on the sensor. Refer to
previous sections of this chapter for electrical connection information.

WARNING:

Please

follow the standard
precautions for working
with liquids around
electronic components.

Use of safety measures when working with liquids around electronics
cannot be stressed enough. Make sure the NC30+ is physically secure
before connecting any tubing or electrical cables. Use Personal
Protection Equipment, such as face shields, protective garments and
gloves, whenever working around hazardous liquids.

1. Make sure that there is no flow of liquid in the system and power is

removed from the

NC30+

.

Note:

When connecting

flare fittings to the NC30+,
do

NOT

use a wrench or

other tool to tighten the
flare nut! Doing so will
damage the instrument,
tubing or nut. The
connections

MUST

be

finger-tight

only.

2. Connect the liquid source to the

NC30+

’s Inlet nozzle using the

provided ¼" flare tubing. Make sure the tubing is inserted firmly
onto the nozzle and the knurled nut is finger tight only.

3. Connect the liquid drain to the

NC30+

’s Outlet nozzle using the

provided ¼" flare tubing. Make sure the tubing is inserted securely
onto the nozzle and the knurled nut is finger tight only.

4. Turn the liquid system on and allow liquid to flow through the

NC30+

, making sure that there are no leaks at the sensor’s inlet or

outlet or any other connections.

WARNING:

If a leak

occurs anywhere within
the system, immediately
stop the flow of liquid
and repair the leak!

5. If leaks occur, immediately stop the flow of liquid. Disconnect and

clear the flare fittings and connectors of debris or burrs. Repair any
other leak(s) and return to Step 1 of this section.

6. If no leaks occur, connect power to the

NC30+

.

7. Make sure the sample liquid is bubble-free - bubbles will be

counted as particles and in large amounts may cause sensor errors.

8. Allow liquid to flow through the sensor for 10 minutes or until

there are no bubbles and the Service LED is OFF. If the Service
LED comes on and remains on, the flow cell should be cleaned (see

Appendix B, “Maintenance”

for cleaning instructions).

9. If there are no leaks and the service LED is off, the instrument is

ready to configure the communications - refer to

Chapter 4,

“Communications”

.

«
...
29
30
31
32
33
...
»

Содержание NanoCount 30+































































































Отзывы:

Нет отзывов

Похожие инструкции для NanoCount 30+

Бренд: Crane Страницы: 11

Бренд: Precision Digital Corporation Страницы: 46

Бренд: E-Pos Страницы: 23

Бренд: BEKA Страницы: 61

Бренд: Nautilus Hyosung Страницы: 154

Бренд: Eaton Страницы: 20

Бренд: Particle Measuring Systems Страницы: 76

Бренд: Sam4s Страницы: 238

Бренд: TEC Страницы: 97

Бренд: Casio Страницы: 1

Бренд: Casio Страницы: 3

Бренд: Omron Страницы: 2

Бренд: Omron Страницы: 28

Бренд: VISIONARY DESIGNS Страницы: 2

Бренд: Tektronix Страницы: 82

Бренд: Magner Страницы: 22

Cash Control Unit 1.0

Бренд: Giesecke & Devrient Страницы: 31

Shelleymatic SH2C-74-NU

Бренд: Delfield Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды