LG-Nortel IP LDK-20 Скачать руководство пользователя страница 548

Страница: 548 / 581

IP LDK-20 Programming Manual Quick

ADMIN Programming table

532

PGM FLEX

ITEM

RANGE

DEFAULT

REMARK

ACNR Tone Detect

Timer

001-300

(3 digits)

030

(sec)

This timer is invoked upon completion of dialing

and system considers the CO party is busy

when the CPTU cannot detect the valid tone

type until this timer expires.

Automatic CO Release

Timer.

020 – 300

(3 digits)

030

(sec)

Uncompleted CO line call will be automatically

released after this timer.

CCR Inter-Digit Timer

000 – 255

(3 digits)

030

(100ms)

This timer is used for the CCR inter-digit timer

in the DISA/DID CO line. In DID type 2, it is

used for DID inter-digit timer.

CO Call Drop Warning Timer

00 – 99

(2 digits)

(sec)

If prepaid money is going to expire during a CO

call, system will give warning tone, and after

this time, the call will be disconnected. This

timer is also used for call drop warning in

Unsupervised Conference.

CO Call Restriction Timer

00 – 99

(2 digits)

(min)

If this value is set to 0, time of outgoing CO call

is not restricted.

If this value is set to non-zero, outgoing CO call

is disconnected after this time.

CO Dial Delay Timer

00 – 99

(2 digits)

(100ms)

Voice connection to the outside party will be

made after this timer. This can be used to

prevent illegal dialing in case of slow response

from the Central Office Line or PBX.

CO Release Guard Timer

001 – 150

(3 digits)

020

(100ms)

This ADMIN program sets the amount of time

before a CO line can be re-seized, after the CO

call disconnects,

This timer controls the time necessary to

guarantee idle loop state when the line is

released.

CO Ring Off Timer

010 – 150

(3 digits)

060

(100ms)

This timer is to secure time interval between

incoming ringing signals so that the active

ringing can be lasted in the system until this

timer is expired.

CO Ring On Timer

1 – 9

(1 digit)

(100ms)

This timer controls the time necessary to detect

an incoming CO call as ringing into the system.

180

CO Warning Tone Timer

060 – 900

(3 digits)

180

(sec)

Determines the amount of time before receiving

warning tone in order to remind the call elapsed

time in case of outgoing CO line conversation

(Only for Korea).

Содержание IP LDK-20






































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IP LDK-20

Отзывы:

Похожие инструкции для IP LDK-20

Бренды по названию

Популярные бренды

LG-Nortel IP LDK-20, Руководство по программированию

Результаты поиска

Содержание IP LDK-20

Отзывы:

Похожие инструкции для IP LDK-20

Бренды по названию

Популярные бренды