LG-Ericsson ipldk-60 Скачать руководство пользователя страница 330

Страница: 330 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

PGM

129

Flex

Btn

Description

Default

Values

VMIB Message

Password

The Voice Mailbox may require entry of a valid system password for access to the

mailbox.

0 (Off)

0 = Off

1 = On

VMIB Message

Time

If this parameter is set to ‘On’, the VMIB will play the Date and Time stamp for each

message before playing the message.

0 (Off)

0 = Off

1 = On

VMIB Message

Type

This parameter defines the order in which messages are retrieved from the Voice

Mailbox, LIFO (Last-In First-out) or FIFO (First-in First-out).

0 (LIFO)

0 = LIFO

1 = FIFO

VMON

The system can be configured notify the user of new messages over an outbound

telephone call.

0 (Disable)

0 = Disable

1 = Enable

VMON CO Grp

When Outbound Notification is enabled, the CO Line group to use to place the

outbound notification call can be configured.

01 ~ 24

VMon Telephone

Number

When Outbound Notification is enabled, the telephone number to call must be

assigned.

digits

VMON Retry

Count

Should the notification fail, error, busy, or no-answer, the system will retry the

outbound call up to 9 times. After the number of attempts, the system abandons the

notification.

1 ~ 9

VMON Retry

Interval

Should the notification fail, the system will attempt the call again after the “VMON

Retry Interval” time.

10 seconds

01 ~ 60 seconds

Cascade

Destination

The system can send a copy of a received voice mail to another Voice mailbox.

Flexible button 1 = Station

Flexible Button 2 = Voice Mailbox number

Button 1 – Station

Number

Button 2 – Voice

Mailbox Number

Cascade Type

The system will send a copy of a new message under one of several conditions as

assigned here.

0 (No cascade)

0 – No Cascade

1 – Immediate

2 - Notify Failure

3 - Urgent

Содержание ipldk-60

































































































































































































































































































































































































































































































































Результаты поиска

Содержание ipldk-60

Отзывы:

Похожие инструкции для ipldk-60

Бренды по названию

Популярные бренды

LG-Ericsson ipldk-60, Описание функций и руководство по эксплуатации

Результаты поиска

Содержание ipldk-60

Отзывы:

Похожие инструкции для ipldk-60

Бренды по названию

Популярные бренды