Lexmark 2580+ Скачать руководство пользователя страница 99

Страница: 99 / 122

Parts catalog

7-1

2580+, 2581+, 2590+, 2591+

Go Back

7. Parts catalog

How to use this parts catalog

The following legend is used in the parts catalog:

•

Asm-index

: Identifies the assembly and the item in the diagram. For example, 3-1 indicates Assembly 3

and item number 1 in the table.

•

Part number

: Refers to the unique number that identifies the FRU.

•

Units/mach

: Refers to the number of units actually used in the base machine or product.

•

Units/option

: Refers to the number of units in a particular option. It does not include the rest of the base

machine.

•

Units/FRU

: Refers to the number of units packaged together and identified by the part number.

•

: (Not shown) in the Asm-Index column indicates that the part is procurable but is not pictured in the

illustration.

•

: (Parts Packet) in the parts description column indicates the part is contained in a parts packet.

•

Model information used in the parts catalog:

Asm-
index

Part
number

Units/mach

- OR -

Units/option

Units/
FRU

Description

Model name

Machine
type

9-Wire

24-Wire

Short
carriage

Long
carriage

Network

Lexmark
Forms Printer
2500+ series

2580+

2580n+

2581+

2581n+

2590+

2590n+

2591+

2591n+

Содержание 2580+



























































































































Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды

Lexmark 2580+, Руководство по обслуживанию

Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды