Lexmark 2580+ Скачать руководство пользователя страница 44

Страница: 44 / 122

3-8

Service Manual

2580+, 2581+, 2590+, 2591+

Go Back

Setup mode

Entering Setup mode

Open the operator panel cover to access layer two.

Press

Setup

to put the printer in Setup mode and print the Main Menu.

Press

LineFeed

to print a list of all the available options.

Select any option from the Main Menu by pressing the corresponding button. A new menu prints each time
you press a button, displaying new selections.

After making a selection, the printer prints a page with the changes shown.

Exiting Setup mode

Press

Set TOF

until the printer returns to the Main Menu, or press

Pitch

from any menu containing a

Return to Main Menu

selection.

Press

Set TOF

again to exit Setup mode. New settings are saved only when the printer exits Setup mode.

Note:

If the printer runs out of paper while in Setup mode, load more paper into the tractor pins, and press

Setup

to continue.

Setup menu options

Interface menu options

Menu

Function

Forms Macro options

Customize macros to print a variety of forms.

Data options

Define how information is processed.

Control options

Define how the printer performs basic tasks.

Emulation options

Determine how the printer interacts with
software applications.

Interface options

Define how information is transferred from a
computer to the printer.

Menu

Function

Interface

• Automatically select the printer interface.
• Use the parallel cable.
• Use the USB cable.
• Use the serial cable (only appears if

optional serial adapter is installed).

Honor init

•

Enable

honors the init signal on the

parallel port.

•

Disable

ignores the init signal on the

parallel port.

Содержание 2580+



























































































































Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды

Lexmark 2580+, Руководство по обслуживанию

Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды