Lexmark 2580+ Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 122

background image

Diagnostic aids

3-11

2580+, 2581+, 2590+, 2591+

Go Back

Previous

Next

7.

Close the operator panel cover.

8.

Press

Start/Stop

to set the printer online.

Printing a network setup page

If the printer is attached to a network, print a network setup page to verify the network connection and find the
printer address.

Note:

This function is disabled if a USB cable is connected.

1.

Make sure the printer is on and the paper is loaded.

2.

With a paper clip or the tip of a pen, press the recessed button located just above the Network connection.

3.

Check the first section on the network setup page, and confirm that the status is

Connected

. If the status

is

Not Connected

, the LAN drop may not be active, or the network cable may be malfunctioning. See

Networking service check.

4.

Check the network setup page to find the IP Address and the Fully Qualified Domain Name. The Fully
Qualified Domain Name is useful in situations where the Address changes. For instance, the Address
changes if the printer is moved; however, the Fully Qualified Domain Name does not change.

Note:

The network setup page also provides important network configuration information.

«
...
45
46
47
48
49
...
»

Содержание 2580+



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2580+

SPP 2020 - Photo Printer - 20 Sheets

Бренд: Samsung Страницы: 81

Бренд: Samsung Страницы: 98

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 203

Бренд: Samsung Страницы: 264

Бренд: Samsung Страницы: 228

Бренд: Samsung Страницы: 211

Бренд: Samsung Страницы: 5

Бренд: Samsung Страницы: 92

Бренд: Samsung Страницы: 75

Бренд: Samsung Страницы: 11

Бренд: Samsung Страницы: 206

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 103

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 215

Бренд: Samsung Страницы: 2

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 266

550N - CLP Color Laser Printer

Бренд: Samsung Страницы: 296

Бренд: Samsung Страницы: 276

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды