Lexmark 2580+ Скачать руководство пользователя страница 42

Страница: 42 / 122

3-6

Service Manual

2580+, 2581+, 2590+, 2591+

Go Back

•

Device information

General device information is displayed here.

Flashing firmware

If the device is attached to the network, the firmware can be re-flashed, or upgraded from the web page.

To reflash the firmware, perform the following steps:

Open the Configuration page of the web server.

Click the

Update firmware

link.

Click the

Browse

button.

A standard Windows file browse dialog will open. Search for the desired flash file.

When the file is found, click

Submit

Importing and exporting INA settings

If the INA needs to be replaced, the internal settings can be downloaded to a file.

To export the INA settings, perform the following tasks:

Click the

Export settings

link from the Configuration page. The following page will display:

In the file save dialog, click

Save

Содержание 2580+



























































































































Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды

Lexmark 2580+, Руководство по обслуживанию

Результаты поиска

Содержание 2580+

Отзывы:

Похожие инструкции для 2580+

Бренды по названию

Популярные бренды